A 200 W lightbulb will convert approximately 24 kWh of electrical energy to light and thermal energy in one day.
This is calculated using the following formula: Energy (kWh) = Power (kW) x Time (hours): 24 kWh = 0.2 kW x 120 hours (assuming the lightbulb is on for 12 hours each day).
Electrical energy is a type of energy that results from the flow of electric charge. It is a form of energy that is transferred when an electric current flows through a wire or conductor, and it is typically measured in units of joules (J) or kilowatt-hours (kWh).
Thermal energy, on the other hand, is the energy that is associated with the temperature of a substance. It is a form of internal energy that is present in all substances, and it can be transferred from one substance to another through conduction, convection, and radiation.
Read more about the topic energy:
https://brainly.com/question/13881533
#SPJ11
a rod undergoes a change in temperature. the change in length is: a rod undergoes a change in temperature. the change in length is:
It is a linear expansion, when a rod undergoes a change in temperature and there is a change in its length.
The length that a rod changes to as a result of a temperature change relies on the rod's initial length, the rate of temperature change, and the material's coefficient of linear expansion. The formula for linear expansion is:
ΔL = αL₀ΔT
Where ΔL is the change in length of the object, is the coefficient for linear expansion of the material in question, and L₀ is the initial length of the object.
Volumetric expansion refers to change in one dimension (volume), whereas linear expansion refers to change in one dimension (length) (volumetric expansion). The area thermal expansion coefficient connects a material's area changes to temperature changes.
To know more about linear expansion, refer:
https://brainly.com/question/19495810
#SPJ4
Complete question is:
A rod undergoes a change in temperature. the change in length is:
A. linear expansion
B. volumetric expansion
would a point closer to the center of the hard drive have a higher, lower, or the same linear acceleration?
A point closer to the center of the hard drive will have a lower linear acceleration than a point farther from the center. This is due to the fact that linear acceleration is inversely proportional to the radius of rotation. The acceleration is greatest at the outer edges and decreases toward the center.
Linear acceleration is the rate of change of the velocity of an object that moves in a straight line. It is also referred to as the object's increase in speed or decrease in speed. The same concept applies when it comes to hard drives.
It is pertinent to understand that linear acceleration decreases when the radius of the disk decreases, which means that the closer the point is to the center, the lower the linear acceleration would be. This is why the outermost tracks have higher transfer rates and are utilized more for storing data on hard drives.
Read more about acceleration :
https://brainly.com/question/460763
#SPJ11
A student builds an electromagnet using a variable power source and 40 turns of wire. The electromagnet is used to pick up metal paper clips. The student changes the voltage and counts the number of paper clips that are picked up. Which table could be the data the student collected?
Table A
Table B
Table C
Table D
The table that could be the data the student collected is table D.
What is an electromagnet?An electromagnet is described as a type of magnet in which the magnetic field is produced by an electric current and usually consist of wire wound into a coil.
If student builds an electromagnet using a variable power source and 40 turns of wire. We have it that the student changes the voltage and counts the number of paper clips that are picked up. The table described below could perfectly described the scenario.
This is Table D
Voltage (V)
3
6
9
12
Number of paper clips
9
18
27
36
Learn more about electromagnet at: https://brainly.com/question/12555869
Why a liquid needs a container when a solid does not?
The correct option is B, a liquid needs a container when a solid does not Solids have definite shapes, and liquids fill their containers.
Solids are one of the three fundamental states of matter, along with liquids and gases. In a solid, the molecules are tightly packed together, and the substance maintains a fixed shape and volume. The particles in a solid are held together by strong intermolecular forces, which prevent them from moving freely.
Solids have many properties that distinguish them from other states of matter. For example, they are usually denser and more rigid than liquids and gases. Solids can also be classified into different types based on their internal structure, such as crystalline solids, which have a regular and repeating pattern of atoms, and amorphous solids, which lack a definite long-range structure.
To learn more about Solids visit here:
brainly.com/question/17061172
#SPJ4
Complete Question: -
Which best describes why a liquid needs a container when a solid does not?
A. Solids fill their containers, and liquids have definite shapes.
B. Solids have definite shapes, and liquids fill their containers.
C. Solids particles do not expand to fill their containers, and liquid particles do.
D. Solids particles expand to fill their containers, and liquid particles do not.
a new block of mass m is used. this block is made of a material that makes an elastic collision with the rod when the block and rod collide. will the hiehgt h increase, decrease, or stay the same?
The height h will stay the same when a new block of mass m is used and makes an elastic collision.
Thus, the correct answer is to stay the same.
What is an elastic collision?An elastic collision is a type of collision in which the total kinetic energy of two or more bodies involved in the collision is conserved. In this collision, the colliding bodies return to their initial state before the collision. That is, the total momentum and kinetic energy are conserved.
As a result, the initial and final energies of the system remain the same, implying that the height of the rod will stay the same as before. So, the height h will stay the same.
For more information about elastic collision refers to the link: https://brainly.com/question/2356330
#SPJ11
helppp pleaseeee enough points
The resistance of the copper wire of length 4 m and diameter 0.002 m is 2.25×10⁻² ohms.
What is resistance?Resistance is the opposition to the flow of current in a circuit.
To calculate the reistance of the copper wire, we use the formula below.
Formula:
R = 4ρL/πd².................. Equation 1Where:
R = Resistance of the copper wireρ = Resistivity of the copper wire at 20°CL = Length of the copper wired = diameter of the copper wireπ = constant called PieFrom the question,
Given:
d = 0.002 mL = 4 mρ = 1.77×10⁻⁸ ohm-metreπ = 3.14Substitute these values into equation 1
R = (4×4×1.77×10⁻⁸)/(3.14×0.002²)R = 2.25×10⁻² ohmsHence, the resistance of the copper wire is 2.25×10⁻² ohms.
Learn more about resistance here: https://brainly.com/question/29635283
#SPJ1
What is the contour interval of this map?
v
The contour interval on a map represents an elevation difference between two contour lines next to each other.
What exactly does elevation mean?Anything that was previously elevated in height. Altitude is the distance from the sea to a point. Every sixth contour line has an index contour, which is a bolder or thicker line.
Elevation above sea level is the definition of elevation for a location. Around 13,000 feet more than sea level, I believe, is where we are now.
The contour elevation is the difference or distance between the elevation of the contour line. The elevation shift from one contour line to the next remains constant within a single map. Several maps have a contour interval of 40 to 80 feet.
Thus, the elevation difference between two contour lines placed adjacent to one another is represented by the contour interval on a map.
To know more about elevation visit:
brainly.com/question/30929506
#SPJ1
a cell phone battery holds a maximum charge of 1.420 ah. how long will it take a charger to fully charge the battery if it starts with zero charge and is charged at a constant rate of 900.0 ma?
If the cell phone battery starts out with no charge and is charged at a constant rate of 900.0 mA, it will take roughly 5,680 seconds or 94.7 minutes to fully charge.
What is the energy consumption of a phone charger?Electricity consumption for phone chargers is typically 5 watts (W) or less. While some faster chargers can use up to 20 W, the majority of standard chargers are closer to the 5–10 W range. Typically, phone chargers connect to a 120-volt outlet and draw one to two amps.
We can apply the following formula to resolve this issue:
time = (charge / current)
charge = 1.420 Ah x 3,600 C/Ah
= 5,112 C
The charging current is then changed from milliamperes (mA) to amperes (A):
current = 900.0 mA / 1,000 = 0.9 A
We can now enter the values into the formula as follows:
time = (charge / current)
= (5,112 C / 0.9 A)
= 5,680 seconds.
To know more about charge visit:-
https://brainly.com/question/14713274
#SPJ1
The top view below shows a record that is spinning counterclockwise at a constant rate. Which of the following statements are true? Choose all that apply.
-A and B have the same linear velocity
-A has a greater linear velocity than B
-B has a greater linear velocity than A
-A and B have the same angular velocity
-A has a greater angular velocity than B
-B has a greater angular velocity than A
From the top view of the spinning record, we can see that points A and B are at different distances from the center of rotation. Therefore, they have different linear velocities.
A has a greater linear velocity than B: True
B has a greater linear velocity than A: False
A and B have the same linear velocity: False
However, both points A and B are at the same distance from the center of rotation. Therefore, they have the same angular velocity.
A and B have the same angular velocity: True
A has a greater angular velocity than B: False
B has a greater angular velocity than A: False
In summary,
A has a greater linear velocity than B
A and B have the same angular velocity.
For more details about distances click here:
https://brainly.com/question/15172156#
#SPJ11
which of the following appliances has the lowest typical energy costs? (1 point) group of answer choices dishwasher microwave oven washing machine refrigerator
Among the given options, the appliance with the lowest typical energy cost is the microwave oven. Typical energy cost refers to the average amount of money spent on energy usage by an appliance or device over a certain period of time.
Microwave ovens use electromagnetic radiation to cook or heat food, and they are generally more energy-efficient compared to other appliances such as dishwashers, washing machines, and refrigerators. This is because microwave ovens use less power and cook food faster than conventional ovens, reducing energy waste and costs. However, it is important to note that the exact energy cost of an appliance can depend on factors such as its age, model, usage, and energy efficiency rating.
Learn more about microwave ovens: https://brainly.com/question/1120515
#SPJ11
two 4.0cm*4.0cm metal plates are separated by a 0.20-mm-thick piece of teflon. a. what is the capacitance? b. what is the maximum potential difference between the plates?
The capacitance of two metal plates separated by a 0.20-mm-thick is approximately 0.25 pF and the maximum potential difference between the plates is 8.4 kV.
a. The capacitance of two metal plates separated by a 0.20-mm-thick piece of Teflon is approximately 0.25 pF (picofarad).
b. The maximum potential difference between the two metal plates is determined by the permittivity of the dielectric material, which in this case is Teflon.
The permittivity of Teflon is about 2.1 and the capacitance of the plates is 0.25 pF, so the maximum potential difference between the plates can be calculated using the equation:
Vmax = (permittivity * Capacitance) / Area.
Therefore, the maximum potential difference between the plates is 8.4 kV.
For more such questions on capacitance , Visit:
https://brainly.com/question/13578522
#SPJ11
how far is the spring compressed question undergrad physics inclined plane where height is not given
The spring is compressed by 0.84 meters.
The potential energy of the block at the starting point is given by,
mgh = 2 x 9.8 x h, where h is the height of the starting point above the bottom of the incline.
Using the given inclination angle of 37 degrees, we can find h as,
h = 4.8 sin(37) = 2.88 m
We can equate the potential energy at the starting point to the energy stored in the compressed spring and the kinetic energy at the bottom of the incline,
mgh = 1/2 kx^2 + 1/2 mv^2
where x is the distance that the spring is compressed, v is the velocity of the block at the bottom of the incline, and k is the spring constant.
Since the block is sliding without friction, we can use conservation of energy to find v as,
mgh = 1/2 mv^2
v^2 = 2gh
v = √(2gh)
Substituting this expression for v in the earlier equation,
mgh = 1/2 kx^2 + 1/2 m(2gh)
2gh = kx^2/m + 2gh
x^2 = 2ghm/k
x = √(2ghm/k)
Substituting the known values,
x = √(2 x 9.8 x 2 x 2.88 / 1000) = 0.84 m
To know more about spring, here
brainly.com/question/14670501
#SPJ4
--The complete question is, A spring is fixed at the bottom end of an incline of inclination 37∘. A small block of mass 2 kg starts slipping down the incline from a point 4.8 m away (along the inclined plane) from the spring. The spring constant is 1000 N/m. How far is the spring compressed?--
what is it called when you can see one image from one angle and a different image from a different angle?
The phenomenon in which an object appears to be different when viewed from different angles is known as a lenticular image. Lenticular printing is the process of producing these images.
What is Lenticular printing?Lenticular printing is a method of producing a lenticular image, which is a printed image that shifts as the viewing angle changes. Lenticular printing is a method of generating a composite image by interlacing two or more images using a lenticular lens.
A lenticular image is a picture that appears to alter when viewed from different angles. It is formed by placing a sheet of tiny cylindrical lenses or "lenticules" over a photo that has been divided into a number of frames. The frames are interlaced, resulting in a composite image that alters when viewed from different angles.
The lenticular function as lenses, refracting light at various angles and allowing each eye to see a distinct image. To generate the lenticular image effect, the interlaced images must be magnified and printed onto a lenticular lens. The result is a plastic sheet that appears to display a different image depending on the angle of the viewer's gaze.
To know more about lenticulars image:
https://brainly.com/question/8590716
#SPJ11
TRUE/FALSE. when air masses of different densities collide, the less dense air mass is forced to rise through frontal lifting.
TRUE. When air masses of different densities collide, the less dense air mass is forced to rise through frontal lifting.
In meteorology, a front is a transition area between two air masses of different densities. The atmosphere's temperature, moisture content, and wind direction are all influenced by these air masses. The types of fronts are warm, cold, stationary, and occluded fronts. The front types are determined by the characteristics of the air masses and the direction of their movement. The types of the front are Warm front: When a warm air mass replaces a cold air mass, it is called a warm front. Warm fronts typically move more slowly than cold fronts. Cold front: A cold front happens when a cold air mass replaces a warm air mass. They have steeper pressure gradients than warm fronts, and they travel faster. Rain, thunderstorms, and cold temperatures are all common with this type of front. Stationary front: This occurs when two air masses meet and neither advances. There is a lot of rain along the stationary front. Occluded front: This is a type of front that develops when a cold front overtakes a warm front. When the cool air catches up to the warm air, an occluded front forms. The fronts can cause precipitation to fall.
Learn more about air masses at brainly.com/question/12089291
#SPJ11
You're designing an external defibrillator that discharges a capacitor through the patient's body, providing a pulse that stops ventricular fibrillation. Specifications call for a capacitor storing 250 J of energy; when discharged through a body with R = 48 Ω transthoracic resistance, the capacitor voltage is to drop to half its initial value in 10 ms.
A) Determine the capacitance (to the nearest ) 10 μF).
B) Determine initial capacitor voltage (to the nearest 100 V) that meet these specs.
I need both correct answers to 2 significant figures.
a..... 1.04 x 10⁻⁴ Vi
b.... 9500 V
A) Determine the capacitance (to the nearest 10 μF).
First, we should identify the formula that we will use to solve the problem.
The formula that relates to capacitance is:
C = 2E / V². Where C is the capacitance in farads, E is the energy stored in joules, and V is the voltage across the capacitor in volts.
Converting the energy to joules, we have: E = 250J.
Now we know that the voltage needs to drop to half of its initial value in 10 ms. We can use the following formula to calculate the capacitance: C = R x t / ln(Vi / Vf) where R is the resistance in ohms, t is the time in seconds, Vi is the initial voltage, and Vf is the final voltage, which is half of the initial voltage.
B) Plugging in the given values, we get:
C = 48 x 0.01 / ln(Vi / (Vi / 2))Simplifying and solving for capacitance, we get:
C = 1.04 x 10⁻⁴ ViNow we can use the energy formula to solve for Vi:Vi = √(2E / C)
Plugging in the given values, we get:Vi = √(2 x 250 / 1.04 x 10⁻⁴)Simplifying and solving for Vi, we get:Vi = 9469 V
Therefore, the capacitance that meets these specifications is 100 μF and the initial capacitor voltage that meets these specifications is 9500 V, to the nearest 100 V.
Learn more about capacitance
brainly.com/question/28445252
#SPJ11
a net force of 89.0 n propels a 4.00-kg model rocket. after being launched from rest, how fast is the rocket traveling after 2.00 s? enter the numerical value in si units.
A net force of 89.0 n propels a 4.00-kg model rocket. after being launched from the rest, the rocket will be traveling at: a velocity of 44.5 m/s.
The net force of 89.0 N propels a 4.00-kg model rocket. After being launched from rest, the rocket will have an acceleration of 89.0 N/4.00-kg = 22.25 m/s².
After 2.00 seconds, the rocket's velocity will be 2.00s x 22.25m/s² = 44.5 m/s. Therefore, after 2.00 s, the rocket will be traveling at a velocity of 44.5 m/s.
To calculate this, we first need to know the net force of the rocket. This is equal to the thrust of the rocket (F = ma) multiplied by the mass of the rocket (m = 4.00 kg). We can then use this net force to calculate the acceleration of the rocket, which is equal to
F/m = 89.0 N/4.00 kg = 22.25 m/s².
Now that we know the acceleration of the rocket, we can use this to calculate the velocity of the rocket after 2.00 s. To do this, we multiply the acceleration by the time, which in this case is 2.00 s. This gives us an initial velocity of 2.00s x 22.25m/s² = 44.5m/s.
This means that after 2.00 s, the rocket will be traveling at a velocity of 44.5 m/s.
To know more about force refer here:
https://brainly.com/question/13191643#
#SPJ11
a bowling ball has a mass of 6 kg. if you slowly roll the ball off the edge of a table 1.5 m high table, what is the kinetic energy of the ball when it hits the ground?
The kinetic energy of the ball when hits the ground is 88.2 J
The formula for calculating kinetic energy is
KE = 1/2mv²
Where KE is kinetic energy, m is mass, and v is velocity.
We have, the mass of the bowling ball is 6 kg, and it is dropped from a height of 1.5 m, we can calculate its velocity just before it hits the ground as follows:
Potential energy = mgh
Where m = mass of the object = 6 kg
g = acceleration due to gravity (9.8 m/s²), and
h = height from which the object is dropped = 1.5 m
PE = mgh
= (6 kg)(9.8 m/s²)(1.5 m)
= 88.2 J
The potential energy of the bowling ball is 88.2 J.
This is equal to its kinetic energy just before it hits the ground.
Therefore, the kinetic energy of the ball is 88.2 J.
To know more about "kinetic energy": https://brainly.com/question/25959744
#SPJ11
determine the values of the mass m for which this system is, respectively, underdamped, overdamped and critically damped.
The values of the mass m for which the system is underdamped, overdamped and critically damped are m < β/2ω, m > β/2ω, and m = β/2ω, respectively.
To determine the values of mass m for which the system is underdamped, overdamped and critically damped, we need to first understand the underlying mathematics behind damping. Damping is a force that acts on a body to oppose its motion, and the damping coefficient, β, is a measure of how much this damping force opposes the motion.
The damping ratio, ζ, is then a measure of how strong the damping is, in relation to the system's natural frequency. Specifically, ζ = β/2mω ,where m is the mass, and ω is the angular frequency.
Underdamping occurs when ζ is less than one, so when m < β/2ω.
Overdamping occurs when ζ is greater than one, so when m > β/2ω. Critically damping occurs when ζ equals one, so when m = β/2ω.
for such more question on mass
https://brainly.com/question/19385703
#SPJ11
how hard must she pull downward to raise herself slowly at constant speed? the mass of the person plus the bucket is 77 kg .
The person must pull downward with a force equal to her weight, which is approximately 760 N in order to raise herself slowly at a constant speed.
When the person pulls downward on the bucket, there are two forces acting on the system: the force of gravity pulling the person and the bucket down, and the force of the person pulling the bucket up. In order for the person to raise herself at a constant speed, the force she exerts on the bucket must be equal and opposite to the force of gravity pulling her down.
The force of gravity on the person and the bucket is equal to their combined weight, which can be calculated as mass times gravitational acceleration (77 kg x 9.81 m/s^2 = 755.37 N). Therefore, the person must exert a force equal to her weight (approximately 760 N) in order to counteract the force of gravity and raise herself at a constant speed.
Thus, to lift herself up slowly and steadily, the person needs to exert a downward force that is equivalent to her weight, which is around 760 Newtons.
To know more about gravitational acceleration click here:
https://brainly.com/question/30429836
#SPJ11
which of the following are irreversible thermodynamic processes? check all that apply. which of the following are irreversible thermodynamic processes?check all that apply. the slow and adiabatic expansion of a gas the spontaneous flow of heat from a hot body to a cooler body the conversion of work to heat by friction the free expansion of a gas
Answer:
Explanation:
The irreversible thermodynamic processes are:
The conversion of work to heat by friction
The free expansion of a gas
The slow and adiabatic expansion of a gas is a reversible process, while the spontaneous flow of heat from a hot body to a cooler body is a natural, irreversible process, but it is not a thermodynamic process per se.
37. a wheel has a constant angular acceleration of 5.0rad/s2 . starting from rest, it turns through 300 rad. (a) what is its final angular velocity? (b) how much time elapses while it turns through the 300 radians?
This means that it took time of 60 seconds for the wheel to turn through 300 radians
The final angular velocity of the wheel can be calculated using the equation
[tex]$\omega_{f} = \omega_{i} + \alpha \cdot t$,[/tex]
where $\omega_{f}$ is the final angular velocity, $\omega_{i}$ is the initial angular velocity, $\alpha$ is the angular acceleration, and $t$ is the elapsed time. As the wheel starts from rest
($\omega_{i} = 0$),
the final angular velocity is equal to the angular acceleration multiplied by the elapsed time.
Therefore,
[tex]$\omega_{f} = 5.0 \, \text{rad/s}^2 \cdot t$.[/tex]
To find the elapsed time, we can rearrange the equation to get
[tex]$t = \frac{\omega_{f}}{\alpha} = \frac{300\, \text{rad}}{5.0\, \text{rad/s}^2} = 60\, \text{s}$.[/tex]
To learn more about Time :
https://brainly.com/question/30481593
#SPJ11
alston realizes that he wasn't paying attention when thana ran the simulation for which the charge was set to zero, and asks thana to describe the particle's motion. which response is correct?
Thana explains that when the charge is zero, the motion of the particle in the simulation is a straight line with a constant velocity.
The direction of the velocity depends on the initial conditions and the force acting on the particle. If there are no other forces acting on the particle, it will continue to move in a straight line with a constant velocity until it encounters another force or object. This is an example of Newton's First Law of Motion, which states that an object at rest will stay at rest and an object in motion will stay in motion with a constant velocity unless acted upon by an external force. If there is a force acting on the particle, it will change direction or speed up or slow down. This is an example of Newton's Second Law of Motion, which states that the force acting on an object is equal to its mass times its acceleration. The direction of the force is in the same direction as the acceleration. When the charge is zero, the particle does not experience any force, so it moves in a straight line with a constant velocity. This is a simple example of how particles can be modeled using physics simulations.
For more such questions on Physics simulations.
https://brainly.com/question/28522691#
#SPJ11
one cycle of the power dissipated by a resistor ( ) is given by this periodic signal repeats in both directions of time. what is the amplitude of the pwm voltage signal applied across the 500- resistor
The maximum amplitude of the PWM voltage signal applied across the 500-ohm resistor is: Vmax=2*I*R=500*I
The power dissipated by a resistor during one cycle is given by the periodic signal. The PWM voltage signal applied across a 500 Ω resistor is analyzed in this question. The amplitude of the signal is determined below.
Pulse Width Modulation is the PWM. It's a process for varying the pulse width of a square wave, which changes the percentage of time the signal is high to low. The pulse width can be varied to create the desired output signal level. It is frequently utilized in applications where analog signals are required, including control systems, power supplies, and audio systems. The maximum voltage Vm of the PWM voltage signal can be found by calculating the RMS value of the pulse. The root-mean-square value is the square root of the mean of the square of the signal over a given period. If we use a pulse that has a duty cycle of 50%, this formula simplifies to: Vmax=Vm+0.5Vdc where Vdc is the average value of the pulse.
The maximum amplitude can be determined using this formula: Vmax=I*R where I is the current and R is the resistance. The current flowing through the resistor is proportional to the voltage applied to it, and the voltage is proportional to the duty cycle of the PWM signal, which varies from 0 to 1. Thus, the voltage applied to the resistor is proportional to the duty cycle and can be expressed as: V=Vmax*D where D is the duty cycle. Thus, the amplitude of the PWM voltage signal applied across a 500-ohm resistor is: Vmax=2*I*R=500*I. Using this equation, we can determine the maximum amplitude of the PWM voltage signal applied across the 500-ohm resistor.
For more such questions on Pulse Width Modulation.
https://brainly.com/question/29358007#
#SPJ11
if you have an unmarked bar magnet and an identical unmagnetized bar of iron, how can you determine which is the magnet?
Iron that is not magnetic will be drawn to a bar magnet. An atom is like a current loop, if it is not observed than it is a magnet.
A piece of iron, which has magnetic qualities, aligns into two poles when placed in the magnetic field of a bar magnet.
If the north pole reports the side in front of it, it is the north pole, and if the south pole reports the south pole, it is the south pole. A piece of iron, which has magnetic qualities, aligns into two poles when placed in the magnetic field of a bar magnet.
Charges that are in motion within an atom produce electricity. The atoms can act as an equivalent current loop thanks to their rotational orbits. Iron is nevertheless drawn to magnetic fields despite their being no current.
To know more about magnetism, visit,
https://brainly.com/question/12740727
#SPJ4
an incompressible substance with a density of 1000 kg/m3 is isothermally compressed from 100 to 1000 kpa. determine the change in enthalpy. multiple choice question. 900 kj/kg 0 kj/kg 10 kj/kg 0.9 kj/kg
The change in enthalpy is 0 J/kg if the incompressible substance with a density of 1000 kg/m3 is isothermally compressed from 100 to 1000 kpa. Thus, option b is correct.
The given data is as follows:
The density of substance = 1000 kg/m3
In-compression pressure = 100 to 1000 kph
The given substance is incompressible. So its specific volume stays constant during the process. The work done is Zero.
Assuming that the process is Isothermal, the temperature remains steady.
The change in enthalpy is calculated by using the formula:
ΔH = m × C × ΔT
The density of mass is calculated by using the formula,
m = V × ρ = 1 m3 × 1000 kg/m3
m = 1000 kg
Change in enthalpy is calculated as:
ΔH = m × C × ΔT
ΔH = 1000 kg × 0 J/(kg·K) × 0 K
ΔH = 0 J/kg
Therefore we can conclude that the change in enthalpy is 0 J/kg.
To learn more about enthalpy
https://brainly.com/question/24170335
#SPJ4
The complete question is-
an incompressible substance with a density of 1000 kg/m3 is isothermally compressed from 100 to 1000 kph. determine the change in enthalpy. multiple choice questions.
a.900 kj/kg
b. 0 kj/kg
c.10 kj/kg
d.0.9 kj/kg
if the moon enters its waxing crescent phase tonight, then what lunar phase will you see in approximately two weeks? multiple choice question.
If the moon enters its waxing crescent phase tonight, then you will see the First Quarter lunar phase in approximately two weeks.
What is the lunar phase?
The Moon is in a specific position during a lunar phase. During the lunar phase cycle, it passes through four primary phases: the new moon, the first quarter, the full moon, and the last quarter. In the new moon phase, the Moon is between the Sun and Earth, and the side of the Moon visible to us is dark.
In contrast, in the full moon phase, the Moon is on the opposite side of the Earth from the Sun, and the side visible to us is entirely illuminated. The first quarter moon is half illuminated and half in shadow, with the illuminated portion appearing as a semi-circle.
The last quarter moon is also half illuminated and half in shadow, but the illuminated portion appears in the opposite direction from the first quarter moon. If the moon enters its waxing crescent phase tonight, you will see the first quarter lunar phase in approximately two weeks. This phase is also known as a half moon, and it occurs when the moon is one-quarter of the way through its orbit around the Earth.
During the first quarter, the illuminated portion of the moon increases each day, until it reaches the full moon phase.
Learn more about phases of the moon here:
https://brainly.com/question/2285324#
#SPJ11
an electron and a proton are each placed at rest in a uniform electric field of magnitude 498 n/c. calculate the speed of each particle 44.4 ns after being released.
An electron and a proton are placed at rest in a uniform electric field of magnitude 498 N/C. The speed of electron and proton 44.4 ns after being released is -3.87 × 10⁶ m/s and 2.13 × 10³ m/s respectively.
Given data:
Electric field (E) = 498 N/C,
Time (t) = 44.4 ns = 44.4 × 10⁻⁹ s,
Mass of electron (m₁) = 9.11 × 10⁻³¹ kg,
Mass of proton (m₂) = 1.67 × 10⁻²⁷ kg.
Formula:
The acceleration produced in the electric field is given by a = qE/m, where q is the charge of the particle, E is the electric field strength, and m is the mass of the particle.
From the above formula, we can find the acceleration produced by the electric field on the electron and proton as follows:
For electron (q = -e, where e is the charge of an electron)
a₁ = qE/m₁ = -eE/m₁
= -1.6 × 10⁻¹⁹ × 498/9.11 × 10⁻³¹
= -8.73 × 10¹⁴ m/s²
For proton (q = +e, where e is the charge of an electron)
a₂ = qE/m₂ = eE/m₂
= 1.6 × 10⁻¹⁹ × 498/1.67 × 10⁻²⁷
= 4.80 × 10⁷ m/s²
Using the kinematic equation, v = u + at, where u is the initial velocity, we can find the speed of each particle 44.4 ns after being released as follows:
For electron,
v₁ = u₁ + a₁t = 0 + (-8.73 × 10¹⁴) × 44.4 × 10⁻⁹
= -3.87 × 10⁶ m/s
For proton,
v₂ = u₂ + a₂t = 0 + (4.80 × 10⁷) × 44.4 × 10⁻⁹
= 2.13 × 10³ m/s
Thus, the speed of the electron is -3.87 × 10⁶ m/s and the speed of the proton is 2.13 × 10³ m/s.
To know more about electric field, refer here:
https://brainly.com/question/15800304#
#SPJ4
a series circuit is a current divider and a parallel circuit is a voltage divider circuit. select one: a. true b. false
The given statement " A series circuit is a current divider and a parallel circuit is a voltage divider circuit " is True
In a series circuit, the electric current is the same through each component, and the total current is equal to the sum of the currents through each component. Therefore, the current is divided among the components.
In a parallel circuit, the potential voltage across each component is the same, and the total voltage is equal to the sum of the voltages across each component. Therefore, the voltage is divided among the components.
Know more about electric current here:
https://brainly.com/question/2264542
#SPJ11
calculate the acceleration of a 330000- kg jumbo jet just before takeoff when the thrust on the aircraft is 160000 n .
To calculate the acceleration of a 330000-kg jumbo jet just before takeoff when the thrust on the aircraft is 160000 N, we must use Newton's second law of motion. This states that the net force on an object is equal to the product of its mass and acceleration, or F=ma.
Thus, we can rearrange the equation to solve for acceleration, a = F/m. In this case, a = 160000 N/330000 kg = 0.485 m/s2. This means that the jumbo jet will accelerate at 0.485 m/s2 just before takeoff.
To explain further, when an object experiences a force, it will accelerate. The acceleration is determined by the size of the force, the mass of the object, and the direction of the force. In the case of the jumbo jet, the force is provided by the thrust of its engines, and the mass of the object is 330000 kg.
As the thrust is 160000 N, the acceleration of the jumbo jet will be 0.485 m/s2. This is the acceleration that the jumbo jet will experience just before takeoff.
To know more about acceleration refer here:
https://brainly.com/question/30660316#
#SPJ11
how many springs does it take to model the thermal energy of diamond and how many for solid argon? explain/justify your answer using appropriate components of the particle model of thermal energy and/or previous models we have used.
In order to model the thermal energy of diamond, 4 springs are required, while the model the thermal energy of solid argon 3 springs are required.
Thermal energy is the internal energy in a substance, that is, the energy of the particles that make up a substance. When two objects at different temperatures come into contact, the heat is transferred from the hotter object to the colder object until both objects reach the same temperature. A system of springs may be used to represent a solid. The particles of a solid are represented by the springs, which are elastic. The more energy the system has, the more the springs will vibrate.
The particle model of thermal energy is based on the idea that all matter is made up of tiny particles that are constantly in motion, and that the faster these particles move, the hotter the object becomes. To model the thermal energy of diamond, four springs are required because diamond is a covalent network solid in which each carbon atom is bonded to four other carbon atoms in a tetrahedral arrangement. Diamond's structure is made up of carbon atoms bonded together by strong covalent bonds. When a carbon atom is bonded to four other carbon atoms, it forms a very strong and stable tetrahedral structure. Diamond's thermal energy is modeled using four springs.
To model the thermal energy of solid argon, three springs are required because argon is a noble gas with a face-centered cubic structure. Solid argon, like other noble gases, has a simple structure. The argon atoms in solid argon are arranged in a cubic array, with an atom at each corner and one in the center of each face of the cube. To model the thermal energy of solid argon, three springs are used. The thermal energy is modeled using these three springs.
Learn more about thermal energy at:
https://brainly.com/question/16953428
#SPJ11