identify the essence of lean manufacturing, an approach developed by toyota as a way of achieving quality, flexibility, and cost effectiveness.

a. True. Because these activities require very little processing power. A basic processor such as an Intel Celeron or AMD Athlon will be more than sufficient for most web browsing and email-checking tasks.

A processor is a part of a computer that carries out operations and carries out instructions. It is in charge of carrying out the calculations and data manipulation necessary for a computer to work. It is the most crucial part of a computer system and is frequently referred to as the "brain" of the computer.

The processor contains an Arithmetic Logic Unit (ALU) which is responsible for carrying out arithmetic and logical operations. It also contains a Control Unit (CU) which is responsible for managing the flow of instructions and data to and from the various components of the computer.

The processor also contains a number of registers which are used to store intermediate results during calculations. The processor also contains several cache levels, which are used to store frequently accessed data and instructions in order to speed up the execution of programs.

Learn more about processor here:

https://brainly.com/question/614196

#SPJ1

Answer:

Increasing the flow tube radius caused flow rate to increase and resistance to decrease. To maintain the same pressure, the pump rate had to increase as well.

The Poisson's ratio for a cast iron with a modulus of elasticity (E) of 110 Gpa and a modulus of rigidity (G) of 44 Gpa is 0.42.

Poisson's ratio is the ratio of transverse strain to corresponding axial strain on a material stressed along one axis. The Poisson's ratio for a cast iron with a modulus of elasticity (E) of 110 Gpa and a modulus of rigidity (G) of 44 Gpa can be calculated as follows:

Poisson's ratio (ν) = (E/2G)-1

ν = (110/2(44))-1

ν = 0.42

Therefore, the answer from the above calculation is 0.42.

Learn more about Poisson's ratio : https://brainly.com/question/30366760

#SPJ11

For letter a, we find that the sample space size is 175,223,510. For letter b the probability is 1 in 175,223,510. And for the letter c, the probability of hitting the Powerball number is 1 in 5,006,386.

For the letter a, we need to find the total number of ways to pick five numbers from 1 to 59 and then multiply that by the number of choices for the Powerball number. Using the combination formula, we get:

As for the letter b, the probability of matching all five numbers in any order plus hitting the Powerball number can be calculated by dividing the number of ways to win by the size of the sample space:

And for the letter c, the probability of picking none of the five numbers but hitting the Powerball number is the probability of picking a number between 1 and 35 correctly and not picking any of the five numbers between 1 and 59. The number of ways to do this is:

Therefore, the probability of matching none of the five numbers but matching the Powerball number is:

Find out more about probability on:

https://brainly.com/question/13604758

#SPJ1

The "wordlist.zip" zip archive is created using this script, which also adds each word from the "wordlist.txt" file as a distinct file. To prevent compression, the compression type is set to ZIP STORED.

The "default password to extract encrypted files" is set using setpassword. The documentation states at the very top: "It presently cannot produce an encrypted file, but it supports decryption of encrypted data in ZIP packages." Try using a software like pyminizip to build a ZIP file that is password-protected.

open a zip file

# Change the dictionary file's name to "wordlist.txt" in the dictionary file setting.

# Set the output zip file's name to "wordlist.zip" in the output zip file setting.

# Change the zip file's password to zip password = "mysecret"

# Use zipfile to create a new zip file that is password-protected.

Using ZipFile(output zip file, mode="w", compression="zipfile.ZIP DEFLATED," allowZip64="True") as myzip

# Use open(dictionary file, "r") as f: for line in f: to open the dictionary file and read its contents line by line.

# Append every word as a separate file, without compression, to the zip file.

line.strip(), compress type=zipfile.ZIP STORED, myzip.writestr

Set a password for the zip file using the following command: myzip.setpassword(bytes(zip password, 'utf-8')).

To know more about wordlist zip visit:-

https://brainly.com/question/30653883

#SPJ1

All the alternatives mentioned are correct, as regards the desired characteristics or values for the parameters of an ideal amplifier.

Here are the desired characteristics or values for the following parameters of an ideal amplifier:

A) Phase shift as a function of frequency: Ideally, an amplifier should have a phase shift of zero across the entire frequency spectrum. This means that the output signal is in phase with the input signal and there is no delay in the signal.

B) Common mode rejection ratio (CMRR): CMRR measures the ability of an amplifier to reject signals that are common to both inputs (such as noise). For an ideal amplifier, the CMRR should be infinite, meaning that it perfectly rejects common-mode signals.

C) Input resistance: An ideal amplifier should have an infinite input resistance. In other words, it should not load down the signal source, and the source should be able to supply the signal without any loss.

D) Output resistance: An ideal amplifier should have zero output resistance, meaning that its output voltage doesn't change regardless of the load connected to its output.

Learn more about amplifier:

https://brainly.com/question/28996974

#SPJ11

The efficiency of a pumping system can be determined by calculating the work input and output of the system.

In this case, the work input is the power supplied to the pump, while the work output is the energy required to raise the water to the tank. The formula for efficiency is:

Efficiency = (Work output/Work input) x 100%

To determine the efficiency of the pumping system, we need to calculate the work output and work input. The work output is the energy required to raise the water to the tank, which can be calculated as follows:

Work output = Force x distance [tex]= mgd[/tex]

where m is the mass of water lifted, g is the acceleration due to gravity, and d is the height difference between the reservoir and the tank. We can calculate the mass of water lifted using the volumetric flow rate and density of water as follows:

[tex]m = Q\rho[/tex]

where Q is the volumetric flow rate and ρ is the density of water.

Substituting the given values, we get:

[tex]m = (42 m^3/min)(1000 kg/m^3) = 42,000\ kg/min[/tex]

The height difference between the reservoir and the tank is given as 16 m. Therefore, the work output is:

Work output [tex]= (42,000 kg/min)(9.81 m/s^2)(16 m) = 6,584,160\ J/min[/tex]

The work input is the power supplied to the pump, which can be calculated using the formula:

[tex]P = Q\rho gH[/tex]

where P is the power, Q is the volumetric flow rate, ρ is the density of water, g is the acceleration due to gravity, and H is the head or height difference.

Substituting the given values, we get:

[tex]P = (42 m^3/min)(1000 kg/m^3)(9.81 m/s^2)(16 m) = 6,584,160\ J/min[/tex]

Therefore, the efficiency of the pumping system is:

Efficiency = (Work output/Work input) x 100% [tex]= (6,584,160/6,584,160) * 100%  \\= 100[/tex] %

Therefore, the efficiency of the pumping system is 100%.

Learn more about efficiency here:

https://brainly.com/question/21329931

#SPJ11

The mineral that makes up this cement is calcite, which is a mineral made up of calcium carbonate (CaCO3).

Calcite is an extremely strong mineral, and when scratched with a steel nail it exhibits the same hardness as the grains of cement. Calcite is a sedimentary rock composed of crystals of calcite, which are formed from the recrystallization of lime mud and limestone. Calcite has an unusual property of effervescing in acid, which is why it is used in cement and mortar. When mixed with other minerals, such as quartz, it produces a strong binding material that is highly resistant to weathering.

The hardness of calcite is due to its crystal structure, which makes it difficult to scratch or break. It is one of the most abundant minerals on Earth and is found in both sedimentary and metamorphic rocks. Thanks to its hardness and durability, calcite is an ideal material for use in cement and mortar.

You can learn more about calcite at: brainly.com/question/11737819

#SPJ11

To calculate the excavation and backfill for the attached trench, we first need to determine the excavation quantity of the earth and backfill stone. The last step is to calculate the backfill quantity of the earth.

Determination of the excavation quantity of the earth is done by measuring the length, width, and depth of the trench and multiplying these values together. For example, if the trench is 10 feet long, 2 feet wide, and 3 feet deep, the total excavation quantity would be 60 cubic feet of earth.

Next, we need to calculate the backfill stone. Assuming the pipe does not require a deduction, the backfill stone quantity is equal to the excavation quantity of earth. Therefore, for the example above, the total backfill stone quantity would be 60 cubic feet.

Finally, we need to calculate the backfill quantity of earth. This is done by subtracting the backfill stone quantity from the excavation quantity. In the example above, the backfill quantity of earth would be 0 cubic feet, since the backfill stone quantity is equal to the excavation quantity.

You can learn more about the excavation at: brainly.com/question/28320627
#SPJ11

Answer:

  2 pieces

Explanation:

You want to know the number of pieces 420 mm × 594 mm can be cut from a sheet that is 600 mm × 1000 mm.

Comparing the dimensions, we see that both dimensions of an A2 piece (420 mm, 594 mm) are shorter than the short dimension of the given sheet. However, the long dimension of the A2 piece will not fit twice in the long dimension of the cast sheet.

2 pieces of size A2 can be cut from the cast sheet.

__

Additional comment

The pieces must be arranged so the long dimension of the A2 piece takes up most of the short dimension of the cast sheet.

The number can also be figured by comparing the areas, as in the attachment. The cast sheet has an area of about 2.4 times the area of an A2 piece.

The plunge and bearing of the lineation are 248° and 315.5°NW, respectively

The slip lineation on the fault plane has a rake of 68° NE. Rake is the angle between the strike of the lineation and the fault. The fault is oriented N52°E and 83°SE. To calculate the plunge and bearing of the lineation, first, calculate the fault plane normal vector:
Fault plane normal vector = N52°E + 83°SE = 135.5°SE
Next, calculate the plunge and bearing of the lineation by taking the rake of the lineation and adding 180° to it.
Plunge = (68° + 180°) = 248°
Bearing = (135.5°SE + 180°) = 315.5°NW

You can learn more about lineation at: brainly.com/question/18556538

#SPJ11

A ramjet is to propel an aircraft at mach 3 at high altitude where the ambient pressure is 8.5 kPa and the ambient temperature t0 is 220 K. The turbine inlet temperature T is 2540 K.

for more such question on  friction less

https://brainly.com/question/30854343

#SPJ11

There are three support reactions, the problem is statically determinate, and the structure is stable.

There are three support reactions on the beam AB: one at each end and one at the middle support.

Yes, this problem is statically determinate. A structure is statically determinate when the number of unknowns (support reactions) equals the number of equations (force balance equations). In this problem, there are three support reactions and three equations of equilibrium.

The structure is stable, meaning that it will remain in its current configuration without any deformations. This can be seen by considering the equilibrium of forces in the vertical direction. There are two forces pushing down on the beam (the load and the reaction at the left end) and one force pushing up (the reaction at the right end). The net force is down, so the structure is stable.

You can learn more about support reactions at: brainly.com/question/19260256

#SPJ11

True, for the modified Goodman diagram, states of completely-reversing stress appear on the horizontal axis.

What is the Goodman diagram?

A Goodman diagram is a plot of the mean stress versus the alternating stress that aids in determining the fatigue endurance of a material. It is named after its creator, Walter Goodman, and is also known as a Goodman plot, a Haigh diagram, or a modified Gerber diagram. The Goodman diagram was created to determine the fatigue endurance of metallic materials that are subjected to varying tensile and compressive loads, such as machinery or structures under dynamic loading, such as aircraft, automobiles, and trains, among others.

Goodman Diagram and Completely-Reversing Stress: In the modified Goodman diagram, the states of completely-reversing stress appear on the horizontal axis. If one stresses the material equally in both the positive and negative directions, it is called a completely reversing stress. The reversing stress can be a fully reversed alternating stress, a zero mean stress, and a reversing torsion in the form of an alternating torque. The Goodman diagram also specifies a limiting line above which the material cannot withstand any more stress without failing, known as the material's endurance limit or fatigue strength limit. The Goodman Diagram is used to analyse the different kinds of stresses which are affecting the component of a structure. These stresses may include alternating and completely reversing stresses. One of the most important features of this diagram is its ability to detect the failure of a material due to the effect of the reversing stress.

Learn more about Goodman diagram here:

https://brainly.com/question/29664433

#SPJ11

The criteria for matching streams above the pinch for designing heat exchangers is to make sure that the hot stream and the cold stream are both having the same temperature. The criteria for matching streams below the pinch is to make sure that the hot stream and the cold stream have the same heat capacity.

These criteria are needed to ensure that there is an efficient heat exchange, meaning that the hot stream will give up most of its heat to the cold stream. In order for this to occur, it is essential that the temperature and heat capacity of the two streams are similar. If the temperatures of the hot and cold streams are too different, the efficiency of the heat exchange will be greatly reduced.

Similarly, if the heat capacities of the hot and cold streams are too different, the heat exchange will not be efficient. Thus, these criteria are necessary for efficient heat exchange.

You can learn more about heat exchangers at: brainly.com/question/22595817

#SPJ11

1) Gain (A) = (Vout / Vin) = 1 + (Rf / Rin)

2) Yes

3) The maximum AC peak to peak voltage input would be (10V / 11) = 0.91V.

4) the output signal will be clipped at the maximum output voltage peak to peak

1. The gain formula for a non-inverting op amp is given by the following equation:

Gain (A) = (Vout / Vin) = 1 + (Rf / Rin)

Where R(f) is the feedback resistor and R(in) is the input resistor.

2. Yes, there is a maximum output voltage peak to peak. The maximum output voltage peak to peak is equal to the voltage supply minus the voltage drop across the diodes. In this case, it would be 10V peak to peak.

3. The maximum AC peak to peak voltage input would be determined by the maximum output voltage peak to peak divided by the gain. The maximum AC peak to peak voltage input would be (10V / 11) = 0.91V.

4. When the input signal is above the maximum peak to peak input voltage, the output signal will be clipped at the maximum output voltage peak to peak. This means that the output signal will be distorted and will not accurately represent the input signal.

Learn more about "voltage " at : https://brainly.com/question/13521443

#SPJ11

A foundation system consisting of site-cast, reinforced concrete grade beams supported by drilled piers is considered a deep foundation system.

Deep foundation systems are used to transfer structural loads to a lower, more stable depth than a shallow foundation system. Deep foundation systems are used when soils at the surface are not suitable to support the weight of the structure, or when a structure is constructed in an area with deeper water table levels.

Reinforced concrete grade beams are structural elements that are used to provide support for building foundations. They are usually reinforced with steel rebar and have additional strength compared to standard concrete. Drilled piers are cylindrical structures that are constructed by drilling into the earth and then filling them with reinforced concrete. These piers can also be reinforced with steel rebar.

Together, these elements are designed to provide a strong, stable foundation for a structure by distributing the load across a larger area. They can also be used to reinforce existing foundations or to increase the load-bearing capacity of a foundation system. Deep foundation systems can be used for a variety of applications, including buildings, bridges, and other large structures.

You can learn more about the deep foundation at: brainly.com/question/29445505

#SPJ11

Where the above condition is given, here's the solution:

#include <iostream>

#include <vector>

#include <string>

using namespace std;

int main() {

int numElements, sumQuantity = 0;

string colorAsked;

unsigned int i;

cin >> numElements;

vector<string> colorList(numElements);

vector<int> quantityList(numElements);

for (i = 0; i < colorList.size(); ++i) {

   cin >> colorList.at(i);

   cin >> quantityList.at(i);

}

cin >> colorAsked;

for (i = 0; i < colorList.size(); ++i) {

   if (colorList.at(i) == colorAsked) {

       cout << "Index " << i << endl;

       sumQuantity += quantityList.at(i);

   }

}

cout << "Total: " << sumQuantity << endl;

return 0;

Learn more about vectors on:

https://brainly.com/question/13322477

#SPJ1

The horizontal distance d between the conveyor belt and the pipe is 0.69 meters.

How to solve for the horizontal distance d between the conveyor belt and the pipe?

The problem involves the use of the Pythagorean Theorem in order to determine the horizontal distance d between the conveyor belt and the pipe. Here are the steps to solve the problem:

1. Draw a diagram representing the problem.

2. Label the values given. The height of the conveyor belt is 0.77 meters and the horizontal distance from the edge of the conveyor belt to the vertical line passing through the pipe is 0.4 meters.

3. Use the Pythagorean Theorem. Let d be the horizontal distance between the conveyor belt and the pipe. Then, the horizontal distance between the edge of the conveyor belt and the pipe is given by (d − 0.15).

By Pythagoras' Theorem, we have: [tex](d - 0.15)^2 + 0.77^2 = d^2[/tex]

4. Simplify the equation. Expanding [tex](d - 0.15)^2[/tex], we get: [tex]d^2 - 0.3d + 0.0225 + 0.77^2 = d^2[/tex]

5. Cancel out d². We are left with: [tex]-0.3d + 0.0225 + 0.77^2 = 0[/tex]

6. Rearrange the equation. We get: [tex]-0.3d = -0.6825.[/tex]

7. Divide both sides of the equation by -0.3. The value of d is then given by [tex]d = 0.69[/tex]. This is the horizontal distance between the conveyor belt and the pipe.

The horizontal distance d between the conveyor belt and the pipe is 0.69 meters.

Learn more about Pythagorean Theorem here:

https://brainly.com/question/343682

#SPJ11

The question at hand is: Examine the following Entity and decide which rule of Normal Form is being violated:

ENTITY: CLIENTATTRIBUTES:# CLIENT IDFIRST NAMELAST NAMESTREETCITYZIP CODE. The entity "CLIENT" violates the third rule of normal form (3NF). This rule states that all attributes must be functionally dependent on the primary key. In this case, the primary key is CLIENT ID, but the attributes FIRST NAME, LAST NAME, STREET, CITY, and ZIP CODE are not functionally dependent on it. To be in 3NF, each of these attributes would need to be related to CLIENT ID in such a way that they could not be determined by any other attribute.

For example, a separate entity for ADDRESS could be created with STREET, CITY, and ZIP CODE as attributes, and then related to the CLIENT entity through a foreign key.

To learn more about Entity attributes : https://brainly.com/question/13438918

#SPJ11

A device that will produce an electrical current when a turbine is used to rotate an iron core wrapped with a coil of wire near a magnet is a generator.

A generator is a device that uses electromagnetic induction to convert mechanical energy into electrical energy. It operates on the basis of the Faraday Law of Electromagnetic Induction, which states that a current is induced in a conductor that is moving through a magnetic field.

The following components are found in a basic generator:

1) rotating magnetic field 2) rotating armature 3) wires 4) coils 5) commutator 6) brushes

Generators are used in a variety of applications, including power plants, wind turbines, and hydroelectric facilities. They are essential for converting mechanical energy into electricity. They have also been utilized as backup power supplies for homes and businesses.

Learn more about "Magnetic field" at: https://brainly.com/question/23096032

#SPJ11

For FM modulation, the in-phase and quadrature components can be determined by differentiating the phase of the modulating signal with respect to time. The envelope can be determined by taking the absolute value of the modulated signal, and the phase can be determined by taking the phase angle of the modulated signal.

For PM modulation, the in-phase and quadrature components can be determined by integrating the phase of the modulating signal with respect to time. The envelope can be determined by taking the absolute value of the modulated signal, and the phase can be determined by taking the phase angle of the modulated signal.

To learn more about PM FM modulation :

https://brainly.com/question/30035950

#SPJ11

Answer:

Technician A is correct. A DMM should be used to check voltage values on the PCM. A spark plug tester should be used to check for spark at one of the spark plugs.

Assuming the lower arm is rigid and the acceleration due to gravity is 9.8 m/s2, the vertical tensile force generated by the triceps muscle is calculated by the formula F = mg + 160N. In this case, F = (1.5 kg)(9.8 m/s2) + 160N = 23.7N.

Given a procedure to evaluate the strength of the triceps muscle, a person pushes down on a load cell with the palm of his hand as indicated in the figure. If the load-cell reading is 160 N, the vertical tensile force f generated by the triceps muscle can be determined by using the following formula: f = (mg + M)g - F Let's assume that the weight of the load cell is negligible, which means it is not contributing to the load's weight.

Since we have to find the vertical tensile force f generated by the triceps muscle, we need to first find out the weight of the load mg, which can be calculated as follows: mg = m * g where m is the mass of the lower arm, and g is the acceleration due to gravity which is equal to 9.81 m/s²mg = 1.5 kg * 9.81 m/s²mg = 14.715 N Next, we have to find the distance of the center of mass of the lower arm from the load cell, which is 0.25 m.

So, we can now calculate the moment of the weight about the load cell, which is given by: mg * d = 14.715 N * 0.25 m = 3.67875 Nm The force due to the load cell is 160 N. Hence, the vertical tensile force f generated by the triceps muscle can be calculated as follows: f = (mg + M)g - F f = (14.715 N + 160 N) - (3.67875 Nm / 0.25 m)f = 174.715 N - 14.715 Nm f = 160 N Therefore, the vertical tensile force f generated by the triceps muscle is 160 N.

State any assumptions: We have assumed that the weight of the load cell is negligible.

You can read more about gravity at https://brainly.com/question/940770

#SPJ11

Both technicians A and B could be correct, depending on the severity of the hard spots on the brake drum.

Technician A is suggesting a method of repairing the brake drum by grinding off the hard spots. This method can work if the hard spots are not too severe and the brake drum can still meet the manufacturer's specifications for diameter, runout, and surface finish after grinding.

Technician B is suggesting that the brake drum should be replaced. This is the recommended course of action if the hard spots are too severe, or if the drum has been machined to its minimum allowed diameter, runout, or surface finish.

Learn more about the brake drum:

https://brainly.com/question/21131150

#SPJ11

The correct answer is To determine the minimum size of the THHN copper feeder tap conductor, we need to calculate the ampacity of the tap conductor based on the 75-degree Celsius column of the NEC table 310.16.

First, we need to find the equivalent ampacity of the 225A main breaker panelboard. Since it is a continuous load, we have to multiply it by 1.25. So, 225A x 1.25 = 281.25A. Next, we need to find the percentage of the feeder ampacity required for the tap conductor. The NEC table 310.16 allows tap conductors to have an ampacity not less than one-third of the rating of the overcurrent device protecting the feeder. Therefore, 1200A/3 = 400A. Finally, we can calculate the minimum size THHN copper feeder tap conductor using the following formula: Minimum conductor ampacity = (281.25A - 180A) + 180A = 281.25A Minimum conductor ampacity = 281.25A / 0.8 (derating factor) = 351.56A From the NEC table 310.16, the minimum size THHN copper conductor with an ampacity of 351.56A is 2/0 AWG. Therefore, the minimum size THHN copper feeder tap conductor that can be used is 2/0 AWG.

To learn more about  minimum size click on the link below:

brainly.com/question/29727023

#SPJ1

A 0.85-hp motor is required by a ducted fan to produce a 24-in stream of air having a velocity of 40 ft/s then the efficiency of the fan is 20.47.

The efficiency of a ducted fan is determined by the ratio of power output (the kinetic energy of the air stream) to the power input (the power of the motor). In this case, the power output can be calculated using the following equation:
Power Output = 0.5 x density of air (in kg per meter cube) x velocity of air (in m/s) x cross-sectional area of air (in meter square) x ( square of velocity of air (in m/s))
Since the velocity of the air is 40 ft/s (which is equivalent to 12.19 m/s), the power output can be calculated as follows:
Power Output = 0.5 x 1.2 kg/m3 x 12.19 m/s x (24 in x 24 in) x (12.19 m/s x 12.19 m/s) = 13024.7 Watts
The power input of the motor can be calculated using the following equation:
Power Input = 0.85 x 746 = 634.1 Watts
Therefore, the efficiency of the fan can be calculated using the following equation:
Efficiency = Power Output / Power Input = 13024.7 Watts / 634.1 Watts = 20.47

You can learn more about efficiency at: brainly.com/question/30280642

#SPJ11

For predictive analysis using machine learning, the correct option is (d) data science. The term "data science" is used to describe the techniques and methods employed by statisticians and computer scientists to extract value from data.

It involves obtaining and processing data to provide useful insights, which are then used to make informed business decisions. It is utilized in numerous fields, including healthcare, education, finance, and more. In the field of machine learning, data science is used to build predictive models that aid in the development of algorithms that can anticipate future outcomes.

For example, data science can be used to build a model that predicts which customers are most likely to leave a business, which can be used to create targeted marketing campaigns that incentivize them to stay. Data science is also used to create recommendation engines that predict which products a customer is most likely to purchase based on their purchase history.

Machine learning models have the potential to anticipate future results, while data science can be employed to educate and validate these models.

This necessitates the identification and purification of data, as well as the selection of pertinent variables for the issue at hand. Models are then established and verified for accuracy.

Learn more about machine learning : https://brainly.com/question/25523571

#SPJ11

In an adiabatic flow process, there is no heat transfer between the fluid and its surroundings. The stagnation pressure is the pressure that the fluid would have if it is brought to a complete stop and all of its kinetic energy is converted to pressure energy.

The stagnation pressure-energy equation relates the stagnation pressure to the static pressure, density, and velocity of the fluid:

P_0 = P + (1 ÷ 2) * rho x v²,

where P_0 is the stagnation pressure, P is the static pressure, rho is the density, and v is the velocity of the fluid.

If the adiabatic flow process with a real fluid (with friction) is reversible, then the entropy change of the fluid is zero. This means that the isentropic stagnation pressure at the outlet of the system is equal to the isentropic stagnation pressure at the inlet of the system. In this case, the stagnation pressures at the inlet and outlet of the system can be equal, even if there is friction present.

However, if the adiabatic flow process is irreversible, then the entropy change of the fluid is greater than zero, and the isentropic stagnation pressure at the outlet of the system is less than the isentropic stagnation pressure at the inlet of the system.

Learn more about adiabatic flow from

https://brainly.com/question/15046687

#SPJ1

All other factors being equal, increasing the stroke volume in a pumping system would normally result in raising the pump rate.

It implies to increase the head of the pump while decreasing the length of the pumping system pipe and to increase the flowrate of the centrifugal pump while lengthening the pipe.

While increasing pressure alters the fluid's velocity, it also reduces flow or output. The volumetric efficiency of the pump and the slower motor speed are the two causes of the flow reduction.

To know more about pumping system visit:-

https://brainly.com/question/15175470

#SPJ1