Wavelength of light = 5 x 10^-7 m = 500 nm.Using Young's experiment formula, we can find the wavelength of the light.
Youthful's trial is an exemplary examination in material science that exhibits the wave-like nature of light. In this trial, light is gone through two cuts and the subsequent impedance design is seen on a screen. The distance between the cuts is known as the cut partition, indicated by "d", and the separation from the cuts to the screen is known as the screen distance, signified by "D".The distance between the focal most extreme and the third dim band is known as the third-request dim periphery, indicated by "x". We are given that the cut partition, d, is 1.5 x 10^-4 m, the screen distance, D, is 1.0 m, and the third-request dim periphery, x, is 1 cm (or 0.01 m).To decide the frequency of the light, indicated by λ, we can utilize the accompanying recipe:
λ = (xd)/D
Subbing the given qualities, we get:
λ = (0.01 m)(1.5 x 10^-4 m)/(1.0 m) = 1.5 x 10^-7 m = 150 nm
Accordingly, the frequency of the light is 150 nanometers. This is inside the scope of apparent light, which has frequencies between roughly 400 nm (violet) and 700 nm (red). The exactness of this computation is subject to the accuracy of the estimation of the distances in question.
To learn more about young's experiment, refer:
https://brainly.com/question/15577226
#SPJ4
a(n) is rock in space. when it enters a planet's atmosphere it is a(n) . any piece remaining after impact is a(n)
A meteoroid is a rock in space. When it enters a planet's atmosphere it is a meteor. Any piece remaining after impact is a meteorite.
A meteoroid is a space rock that is too small to be considered an asteroid. The term meteoroid refers to small bodies that range in size from tiny particles to around one meter in diameter. A meteoroid that enters Earth's atmosphere and vaporizes is known as a meteor or shooting star, while the remains that hit the ground are known as meteorites.
Meteoroids that hit Earth are believed to be debris from asteroids or comets. The majority of meteoroids that enter Earth's atmosphere are small and burn up in the atmosphere, producing a bright tail as they do so.
Learn more about meteor at https://brainly.com/question/7993266
#SPJ11
a ball thrown vertically upward is caught by the thrower after 2.80 s at the same height as the initial point of release. find the maximum height the ball reaches from the point of release.
The maximum height reached is 99.6.
The velocity of the ball at the highest point. When the ball reaches the highest point, its velocity is zero. Therefore, we can use the following formula to find the velocity at the highest point: v = u - gt
where:v is the final velocity (which is zero)u is the initial velocity. g is the acceleration due to gravityt is the time taken to reach the highest pointWe know that the ball takes 2.80 seconds to reach the thrower.
Therefore, it takes half of that time, or 1.40 seconds, to reach the highest point. We also know that the ball was thrown vertically upward, which means that the initial velocity was positive (upward).
Therefore, 0 = u - g(1.40)Solving for u, we get:u = g(1.40) = 9.8(1.40) = 13.72 m/s.
The maximum height: h = ut - ½gt²
where:h is the maximum height. u is the initial velocity (which is 13.72 m/s)t is the time taken to reach the highest point (which is 1.40 seconds)g is the acceleration due to gravity (which is 9.8 m/s²)
h = (13.72)(1.40) - ½(9.8)(1.40)² = 9.60 m.Therefore, the maximum height the ball reaches from the point of release is 9.60 m.
An alternative approach that can also be used is to use the formula:v² = u² + 2ghwhere:v is the final velocity (which is zero)u is the initial velocity. g is the acceleration due to gravityh is the maximum height.
0² = (13.72)² + 2(-9.8)hh = (13.72)²/2(9.8) = 9.60 m.
to know more about height refer here:
https://brainly.com/question/29131380#
#SPJ11
a fragment of a current-carrying wire has a cross-sectional area that increases as shown. 1) if the current that flows through the wire is uniform, where is the drift velocity the greatest?
According to the given statement, if the current that flows through the wire is uniform, the drift velocity is the greatest at the section of wire with diameter d.
As the current is uniform throughout the wire, so the current through a given cross-sectional area is the same. Also, the current density, J is given by:
J = I/A
where I is the current and A is the cross-sectional area of the wire. Thus, if the area of the cross-section of the wire is more, the current density will be less. The current density is inversely proportional to the area of the wire, i.e. J ∝ 1/A. Hence, the drift velocity is inversely proportional to the current density, i.e. v[tex]_d[/tex] ∝ 1/J.
Thus, the drift velocity is greater where the cross-sectional area is less. So, the drift velocity is greater at the section of wire with diameter d.
So, the answer is at the section of wire with diameter d
Learn more about drift velocity at https://brainly.com/question/4269562
#SPJ11
initially a body moves in one direction and has kinetic energy k. then it moves in the opposite direction with three times its initial speed. what is the kinetic energy now?
The new kinetic energy of the object is 4.5 times its initial kinetic energy, k.
What is kinetic energy?Kinetic energy is the energy of an object due to its movement. It is equal to one-half of the object's mass multiplied by the square of its velocity.
The problem states that initially, a body moves in one direction and has kinetic energy k. Then it moves in the opposite direction at three times its initial speed.
The formula for kinetic energy is,
Ek = 1/2mv²
where, Ek = kinetic energy of the object
m = mass of the object v = velocity of the object
From the problem, the initial kinetic energy of the body is k.
Therefore, Ek1 = k
The body moves in the opposite direction at three times its initial speed.
That means the new velocity (v') of the body is 3v (where v is the initial velocity).
Thus, the new kinetic energy (Ek2):
Ek2 = 1/2m(3v)²
Ek2 = 1/2m(9v²)
Ek2 = 4.5mv²\
The new kinetic energy of the object is 4.5 times.
To know more about kinetic energy:
https://brainly.com/question/22174271
#SPJ11
when you blow air into an open organ pipe, it produces a sound with a fundamental frequency of 440 hz. if you close one end of this pipe, the new fundamental frequency of the sound that emerges from the pipe is
The new fundamental frequency of 880 Hz.
When you blow air into an open organ pipe, it produces a sound with a fundamental frequency of 440 Hz.
If you close one end of this pipe, the new fundamental frequency of the sound that emerges from the pipe is two times the initial frequency, i.e., 880 Hz.
When the air column is confined to one end of the pipe, the first harmonic that can be supported is the third harmonic.
The wavelength of the first harmonic is twice the length of the pipe, and the wavelength of the third harmonic is equal to the length of the pipe.
The frequency of the third harmonic is three times the frequency of the first harmonic.
The new fundamental frequency of the sound that emerges from the pipe is two times the initial frequency, i.e., 880 Hz.
This is because the frequency of the first harmonic is half that of the fundamental frequency in an open organ pipe.
When one end is closed, the first harmonic is no longer available, and the frequency of the second harmonic, which is twice the fundamental frequency, is available.
Therefore, the fundamental frequency is multiplied by two when one end of an open organ pipe is closed to produce a pipe that is open on one end and closed on the other.
This results in a new fundamental frequency of 880 Hz instead of 440 Hz, as observed in an open pipe.
to know more about frequency refer here:
https://brainly.com/question/14316711#
#SPJ11
a 0.500-kg object attached to a spring with a force con- stant of 8.00 n/m vibrates in simple harmonic motion with an amplitude of 10.0 cm. calculate the maximum value of its (a) speed and (b) acceleration, (c) the speed and (d) the acceleration when the object is 6.00 cm from the equilibrium position, and (e) the time inter- val required for the object to move from x 5 0 to x 5 8.00 cm.
(a) The maximum speed of the object is 1.26 m/s.
(b) The maximum acceleration of the object is 25.1 m/s^2.
(c) The speed of the object when it is 6.00 cm from the equilibrium position is 0.98 m/s.
(d) The acceleration of the object when it is 6.00 cm from the equilibrium position is 19.6 m/s^2.
(e) The time interval required for the object to move from x = 0 to x = 8.00 cm is 0.50 s.
(a) The maximum speed of the object can be found using the equation v_max = Aω, where A is the amplitude and ω is the angular frequency.
Thus, v_max = 0.10 m × √(8.00 N/m ÷ 0.500 kg) = 1.26 m/s.
(b) The maximum acceleration of the object can be found using the equation a_max = Aω^2, where A is the amplitude and ω is the angular frequency.
Thus, a_max = 0.10 m × (8.00 N/m ÷ 0.500 kg) = 25.1 m/s^2.
(c) The speed of the object when it is 6.00 cm from the equilibrium position can be found using the equation v = ω√(A^2 - x^2), where x is the distance from the equilibrium position.
Thus, v = √(8.00 N/m ÷ 0.500 kg) × √(0.10^2 - 0.06^2) = 0.98 m/s.
(d) The acceleration of the object when it is 6.00 cm from the equilibrium position can be found using the equation a = -ω^2x, where x is the distance from the equilibrium position.
Thus, a = -(8.00 N/m ÷ 0.500 kg) × 0.06 m = -19.6 m/s^2 (note that the negative sign indicates that the acceleration is in the opposite direction to the displacement).
(e) The time interval required for the object to move from x = 0 to x = 8.00 cm can be found using the equation T = 2π/ω, where ω is the angular frequency.
Thus, T = 2π/√(8.00 N/m ÷ 0.500 kg) = 0.50 s.
To know more about equilibrium position click here:
https://brainly.com/question/30694482
#SPJ11
what kind of star has an absolute magnitude of 10 and a surface temperature of 20,000 k? a. giant b. supergiant c. white dwarf d. main sequence
The kind of star that has an absolute magnitude of 10 and a surface temperature of 20,000 K is c. white dwarf.
A white dwarf is a star that has a low mass that has exhausted all of its nuclear fuel, as well as the ability to generate energy. The stars’ internal gravity pulls the matter of the star together, and they collapse under their own weight. White dwarfs are generally made up of electron-degenerate matter, which is a material made up of tightly packed, positively charged atomic nuclei and negatively charged electrons. The energy of the electrons compresses the nuclei, creating the high density that is required for the star to survive
Stars are classified according to their temperature, size, and luminosity, which are referred to as spectral types. According to their size, stars are divided into four groups: main-sequence, giant, supergiant, and dwarf. A white dwarf is a star that has a low mass and a size comparable to that of Earth.What is absolute magnitude?Absolute magnitude is defined as the brightness of a star when it is measured from a distance of ten parsecs. A parsec is equal to 3.26 light-years. It is critical to remember that absolute magnitude is a measure of a star's intrinsic brightness rather than how bright it appears from Earth.
Learn more about white dwarf at:
https://brainly.com/question/19602278
#SPJ11
a spherical capacitor has vacuum between its conducting shells and a capacitance of 125 pf . the outer shell has inner radius 9.00 cm . what is the outer radius of the inner shell? express your answer with the appropriate units.
For a spherical capacitor with a capacitance of 125 and a vacuum between its conducting shells, the outer radius of the inner shell is around 5.60 cm.
The capacitance of a spherical capacitor is given by:
C = 4πε₀[(r₁r₂)/(r₂-r₁)]
where C is the capacitance, ε₀ is the electric constant (8.85 x [tex]10^{-12}[/tex] F/m), r₁ is the radius of the inner shell, and r₂ is the radius of the outer shell.
In this case, we know that the capacitance C = 125 pF (picoFarads), r₂ = 9.00 cm, and we want to find r₁.
We can rearrange the equation to solve for r₁:
r₁ = (C × r₂)/(4πε₀ + C)
Substituting the values:
r₁ = (125 x [tex]10^{-12}[/tex] F × 0.09 m) / (4π × 8.85 x [tex]10^{-12}[/tex] F/m + 125 x [tex]10^{-12}[/tex] F)
r₁ ≈ 5.60 cm
Therefore, the outer radius of the inner shell is approximately 5.60 cm.
To learn more about the capacitor at
https://brainly.com/question/17176550
#SPJ4
Two trains are moving in the same direction on parallel tracks. Train A is 300 m long and moves at 10 m/s. Train B is 250 m long and moves at 8 m/s. The front of train B is 1 km ahead of the front of train A. How far does Train A travel while both trains overlap?
Train A travels 3,200 meters while both trains (moving in the same direction on parallel tracks) overlap.
To find the distance Train A travels while both trains (on parallel tracks) overlap, we need to:-
1. Determine the relative speed of Train A with respect to Train B. Since both trains are moving in the same direction, we can find this by subtracting the speed of Train B from the speed of Train A: 10 m/s - 8 m/s = 2 m/s.
2. Calculate the initial distance between the two trains. The front of Train B is 1 km (1,000 m) ahead of Train A. Therefore, the distance between the back of Train B and the front of Train A is 1,000 m - 250 m = 750 m.
3. Find the time taken for Train A to catch up with Train B. Divide the initial distance by the relative speed: 750 m / 2 m/s = 375 seconds.
4. Calculate the distance traveled by Train A while both trains overlap. During the overlap, Train A is moving at 10 m/s, so multiply its speed by the time taken to catch up with Train B: 10 m/s * 375 seconds = 3,750 meters.
5. Calculate the overlap distance. The combined length of both trains is 300 m + 250 m = 550 m. Since Train A catches up with Train B, the distance it travels while overlapping is the combined length of both trains: 3,750 m - 550 m = 3,200 meters.
Therefore, Train A travels 3,200 meters while both trains overlap.
Learn more about the direction: https://brainly.com/question/3184914
#SPJ11
a 100 ohm resistor is connect in parallel with a 300 ohm resistor. what is the equivalent resistance?
The equivalent resistance of the two resistors in parallel is 75 ohms.
To calculate the equivalent resistance of a 100-ohm resistor and a 300-ohm resistor connected in parallel, the following formula can be used:
Req = 1 / ((1/R1) + (1/R2))
where Req is the equivalent resistance, R1 is the resistance of the first resistor, and R2 is the resistance of the second resistor.
In this situation, the values of R1 and R2 are 100 ohms and 300 ohms, respectively.
Therefore, we can substitute these values into the equation as follows:
Req = 1 / ((1/100) + (1/300))= 1 / (0.01 + 0.00333)= 1 / 0.01333= 75 ohms
Therefore, the equivalent resistance of the two resistors in parallel is 75 ohms.
Learn more about resistance here:
https://brainly.com/question/29427458#
#SPJ11
how much force does an 76.0 kg astronaut exert on his chair while sitting at rest on the launch pad?
The force exerts by a 76.0 kg astronaut on his chair while sitting at rest on the launch pad is: 746.76 N
According to Newton’s third law, for every action, there is an equal and opposite reaction. The astronaut exerts a force on the chair and the chair exerts an equal and opposite force on the astronaut. If the astronaut is sitting at rest on the launch pad, then he is not moving and hence the net force acting on him is zero.
Therefore, the force exerted by the astronaut on the chair is equal in magnitude and opposite in direction to the force exerted by the chair on the astronaut. In other words, the force that the astronaut exerts on the chair is equal to his weight.
The weight of the astronaut can be calculated using the formula F = m * g, where F is the force, m is the mass, and g is the acceleration due to gravity. The acceleration due to gravity on Earth is approximately 9.81 m/s^2.
Therefore, the force exerted by the astronaut on the chair is F = m * g = 76.0 kg * 9.81 m/s^2 = 746.76 N. Therefore, the astronaut exerts a force of 746.76 N on his chair while sitting at rest on the launch pad.
To know more about force refer here:
https://brainly.com/question/13191643#
#SPJ11
determine the current (in ma) through the led in the circuit below if the forward biased voltage of the led is 2 v?
The current flowing through the LED is also 10 mA. To determine the current (in mA) through the LED in the circuit given below.
Assuming that the forward biased voltage of the LED is 2V, the following procedure is followed: To calculate the current flowing through the LED in the given circuit, the following formula is used: Ohm's Law: V = IR where V is the voltage applied to the circuit, I is the current flowing through the circuit, and R is the resistance of the circuit. Now, in the given circuit, the total voltage applied to the circuit is 12V. Therefore, the voltage across the resistor (R) is V = 12 - 2 = 10V. So, we know that the voltage across the resistor is 10V and the value of the resistor is 1000 ohms.
Therefore, the current through the resistor is: I = V/R = 10/1000 = 0.01 A = 10 mA. Now, this current will also be the current flowing through the LED as the LED is in series with the resistor. Therefore, the answer is 10 mA.
Learn more about Ohm's Law : https://brainly.com/question/231741
#SPJ11
what was the ratio of a weight to its just noticeable difference weight when they were lifted what was the ratio of a weight to its just noticeable difference weight when the weight were placed in the subject's hands?
According to Weber's Law, the ratio of a weight to its just noticeable difference weight when placed in the subject's hands is 1 : 40.
The ratio of a weight to its just noticeable difference weight when it is lifted by a subject is 1 : 40. This implies that if the weight of an object is x, the minimum additional weight that can be added to it and be noticed by a subject is x/40.The ratio of a weight to its just noticeable difference weight when the weight is placed in the subject's hands is 1:20.
This implies that if the weight of an object is x, the minimum additional weight that can be added to it and be noticed by a subject when it is placed in their hands is x/20. The Weber-Fechner Law applies in this scenario. It is a relationship between the intensity of a stimulus and its perceived strength that states that the sensation is proportional to the logarithm of the stimulus' intensity.
Learn more about Weber's Law at https://brainly.com/question/19021235
#SPJ11
how long must a 0.70- mm -diameter aluminum wire be to have a 0.42 a current when connected to the terminals of a 1.5 v flashlight battery?
To determine the length of an aluminum wire required to carry a certain current, one must use the formula: r = (ρL) / (πr²), where r is the radius of the wire, ρ is the resistivity of the wire, and L is the length of the wire is 48.54 m.
What is the length of the wire?A 0.70 mm diameter aluminum wire has a radius of 0.35 mm or 0.00035 m. The resistivity of aluminum is 2.82 × 10⁻⁸Ωm. The formula for current is:
I = V / R
where, V is voltage, and R is resistance. We can rearrange this to:
R = V / I
Plugging in the given values of 0.42 A and 1.5 V gives R = 3.571 Ω. The resistance of a wire is given by:
R = ρL / A
where, A is the cross-sectional area of the wire, and ρ is its resistivity.
We know the resistivity of aluminum and the radius of the wire, so we can calculate the cross-sectional area of the wire:
A = πr² = 3.1416 × (0.00035 m)² = 3.848 x 10⁻⁷ m². Substituting all the values in the formula for the resistance of the wire and solving for L gives:
L = RA / ρ = (3.571 Ω) × (3.848 x 10⁻⁷ m²) / (2.82 × 10⁻⁸ Ωm) = 48.54 m.
Therefore, the aluminum wire must be 48.54 m long to have a current of 0.42 A when connected to the terminals of a 1.5 V flashlight battery.
Read more about length here:
https://brainly.com/question/28322552
#SPJ11
What is the transfer of thermal energy called?
Answer:
Conduction
Explanation:
The process by which heat energy is transmitted through collisions between neighboring atoms
if a 2000-kg car traveling at 30 m/s hits a wall and comes to a complete stop in 0.03 seconds, how much force was applied to the car?
If a 2000-kg car traveling at 30 m/s hits a wall and comes to a complete stop in 0.03 seconds the force that was applied to the car is 6,000,000 N
The force applied to the car can be calculated using the formula:
Force = (mass x change in velocity) / time
Here, the mass of the car is 2000 kg, the initial velocity is 30 m/s, the final velocity is 0 m/s (since the car comes to a complete stop), and the time taken is 0.03 seconds.
Substituting these values, we get:
Force = (2000 kg x (0 m/s - 30 m/s)) / 0.03 s
Force = -6,000,000 N
The negative sign indicates that the force is acting in the opposite direction to the motion of the car. So, the force applied to the car by the wall is 6,000,000 N.
Learn more about force at
https://brainly.com/question/13191643
#SPJ4
A hairdryer has a power of 1.5 KW and was used for 15 minutes how much did it cost?
the loudness and duration of the emitted sound are enhanced by a resonant pipe suspended vertically below the center of the bar. if the pipe is open at the top end only and the speed of sound in air is 340 m/s, what length of the pipe is required to resonate with the wooden bar?
The length of the pipe required to resonate with the wooden bar is equal to one-fourth of the wavelength of the sound produced by the bar. The wavelength of the sound is equal to the speed of sound in air divided by the frequency of the sound.
The frequency of the sound is determined by the type of wooden bar being used. This frequency can range from 20 Hz to 20 kHz depending on the type of bar. Once the frequency is determined, the wavelength can be calculated and the length of the pipe can then be calculated.
The resonant pipe is suspended vertically below the center of the bar, and the pipe is open at the top end only. This means that the pipe is open to the atmosphere and the sound waves can resonant in the pipe. A longer pipe will allow more sound waves to be absorbed and thus the sound will be louder and longer in duration.
The length of the pipe should be equal to one-fourth of the wavelength of the sound for maximum resonance. This will ensure that the sound waves will be amplified and the sound produced will be louder and longer in duration.
Know more about wavelength here
https://brainly.com/question/13533093#
#SPJ11
which of the following is not connected or involved with shock metamorphism? group of answer choices asteroids coesite pegmatites impactiles
Shock metamorphism is a type of metamorphism caused by an impact, such as from a meteorite or an asteroid. So the answer to this question is asteroids.
Shock metamorphism refers to the changes that occur in rocks when they are subjected to high-pressure shock waves caused by impacts from asteroids, comets, or meteorites. The impact creates high temperatures and pressures that cause the mineral composition of the rock to be changed. Coesite and impactites are two common rocks found with shock metamorphism, while pegmatites are not related to shock metamorphism. Impactiles are objects that impact and cause shock metamorphism in rocks. Asteroids and comets are examples of impacts that can cause shock metamorphism. Pegmatites, on the other hand, are coarse-grained igneous rocks that form from the slow cooling of magma.
Learn more about shock metamorphism: https://brainly.com/question/14897584
#SPJ11
what is the torque produced by a force of magnitude 90 n that is exerted perpendicular to and at the end of a 0.5m long wrench
Torque is a measure of the twisting force that is produced when a force is applied to an object and is defined as the product of the force.
The distance from the pivot point to the point of application of the force, multiplied by the sine of the angle between the force vector and the vector from the pivot point to the point of application of the force.
In this case, the force of 90 N is applied perpendicular to the end of a wrench that is 0.5 m long. Assuming the force is applied at the end of the wrench, the distance from the pivot point to the point of application of the force is 0.5 m. Since the force is perpendicular to the wrench.
The angle between the force vector and the vector from the pivot point to the point of application of the force is 90 degrees. Using the formula for torque, the torque produced by the force is: Torque = force x distance x sin(angle)
Torque = 90 N x 0.5 m x sin(90)Torque = 45 Nm
Therefore, the torque produced by the force of magnitude 90 N that is exerted perpendicular to and at the end of a 0.5m long wrench is 45 Nm.
Learn more about force here:
https://brainly.com/question/13191643
#SPJ4
what is the smallest possible magnitude of the acceleration of the electron due to the magnetic field?express your answer with the appropriate units.
The smallest possible magnitude of the acceleration of the electron due to the magnetic field is 0 m/s².
The formula for calculating the magnetic force exerted on a moving charged particle, like an electron, is given by
F = qvB
where F is the force exerted, v is the velocity of the electron,
q is the charge on the electron, and
B is the magnitude of the magnetic field.
Now, we can derive an expression for the magnitude of the acceleration of the electron due to the magnetic field using the above equation:
a = F/m
where a is the acceleration of the electron, and m is the mass of the electron.
In this case, the electron will move in a straight line with constant velocity, and there will be no acceleration.
Thus, F = 0
Therefore, the smallest possible magnitude of the acceleration of an electron due to a magnetic field is zero, when the electron's velocity is perpendicular to the field and its Lorentz force is balanced by an equal and opposite electric force.
Learn more about the Magnitude of the acceleration here:
https://brainly.com/question/1597065
#SPJ11
A light bulb in a battery-powered torch is too dim. Explain
which property of the bulb should be changed to make the light brighter, and how should it be changed
The light is brighter in a battery-powered torch, you should change the wattage or power rating of the bulb. A higher-wattage bulb will produce more light and therefore be brighter. When selecting a new bulb for the torch, make sure to choose a bulb with a higher wattage rating than the current bulb.
A battery is an electrochemical device that converts chemical energy into electrical energy through a chemical reaction. It consists of one or more electrochemical cells, each of which contains a positive electrode (cathode), a negative electrode (anode), and an electrolyte that allows ions to move between the two electrodes.
During the discharge process, a chemical reaction takes place within the battery that causes electrons to flow from the negative electrode through an external circuit to the positive electrode, generating an electrical current. This current can then be used to power a wide range of electrical devices, such as flashlights, smartphones, and cars. The chemical reaction can be reversed by recharging the battery, which involves applying an external electrical current to the electrodes to force the reaction to occur in the opposite direction.
To know more about Battery visit here:
brainly.com/question/19225854
#SPJ4
a gun fires a bullet vertically into a 1.40-kg block of wood at rest on a thin horizontal sheet.if the bullet has a mass of 26.8 g and a speed of 230 m/s , how high will the block rise into the air after the bullet becomes embedded in it?
The block will rise to a height of approximately 4.36 cm after the bullet becomes embedded in it.
We can use the principle of conservation of momentum to solve this problem. The total momentum of the system (bullet + block) before the collision is,
p_before = m_bullet * v_bullet
where m_bullet is the mass of the bullet and v_bullet is its speed.
After the collision, the bullet becomes embedded in the block, so the total mass of the system is,
m_total = m_bullet + m_block
The velocity of the combined bullet-block system after the collision can be calculated using the conservation of momentum,
p_before = p_after
m_bullet * v_bullet = (m_bullet + m_block) * v_after
where v_after is the velocity of the combined bullet-block system after the collision.
Solving for v_after,
v_after = (m_bullet * v_bullet) / (m_bullet + m_block)
Now, we can calculate the kinetic energy of the bullet-block system just after the collision,
KE_after = (1/2) * (m_bullet + m_block) * v_after^2
The initial kinetic energy of the bullet is,
KE_before = (1/2) * m_bullet * v_bullet^2
The difference between these two energies represents the energy that has been transferred to the block,
delta_KE = KE_before - KE_after
This energy is used to raise the block to a certain height h. If we assume that all of this energy is converted into potential energy, then we can write,
delta_KE = m_block * g * h
where g is the acceleration due to gravity.
Solving for h,
h = delta_KE / (m_block * g)
Substituting the expressions for delta_KE, m_block, v_bullet, and v_after,
h = [(1/2) * m_bullet * v_bullet^2] / [(m_bullet + m_block) * g]
Substituting the given values,
h = [(1/2) * 0.0268 kg * (230 m/s)^2] / [(0.0268 kg + 1.40 kg) * 9.81 m/s^2] = 0.0436 m
To know more about bullet, here
brainly.com/question/15684008
#SPJ4
is there an advantage to following through when hitting a baseball with a bat, thereby maintaining a longer contact between the bat and the ball?
Yes, there is an advantage to following through when hitting a baseball with a bat, thereby maintaining a longer contact between the bat and the ball.
The advantage of following through in a baseball game is that it increases the speed of the ball and also the energy associated with the ball's trajectory.
The longer the bat comes in contact with the ball, the greater the energy stored in the ball, and the farther the ball will go. Therefore, it is very important to follow through while hitting the ball with the bat in baseball games, which will result in the ball being propelled much farther than if it had been hit with a minimal follow-through.
Thus, it is beneficial to follow through when hitting a baseball with a bat, thereby maintaining a longer contact between the bat and the ball.
To know more about "energy": https://brainly.com/question/30041286
#SPJ11
in csi detectors there is very little light spread. b. crystalline needles block light from the detector. c. x-rays are converted into an electrical signal. d. light spread causes resolution to decrease.
In CSI detectors, there is very little light spread.
The light spread causes a decrease in resolution. Therefore, it is necessary to prevent light from spreading in the detectors to maintain the desired level of resolution. This is achieved by using a specialized type of detector known as a crystalline needle detector. Crystalline needles are used to block light from the detector. These needles are made from a material that is transparent to x-rays but opaque to visible light. As a result, the needles allow x-rays to pass through them and reach the detector while blocking any visible light that may cause a reduction in resolution. The x-rays that are detected by the detector are converted into an electrical signal. This is done by using a scintillator, which is a material that absorbs x-rays and emits visible light in response. The light emitted by the scintillator is then detected by a photodiode, which converts it into an electrical signal. This signal is then processed by a computer to create an image of the object being scanned. In conclusion, the use of crystalline needle detectors in CSI is critical in ensuring that the desired level of resolution is maintained. By blocking any visible light that may cause a decrease in resolution, these detectors help to produce high-quality images of the object being scanned. The conversion of x-rays into an electrical signal through the use of a scintillator and a photodiode is also important in producing clear and accurate images.
For more such questions on Light.
https://brainly.com/question/30788777#
#SPJ11
always tangent to the track, causes the car to speed up as it goes around. if it starts from rest, its speed at the end of one revolution is:
The force that is always tangent to the track and causes the car to speed up as it goes around is known as the centripetal force.
The force that acts on a body moving in a circular path toward the center of the circle or curve is known as the centripetal force.
If an object moves in a circular path, the direction of the velocity changes, and it is, therefore, an accelerated motion.
Tangential velocity is the velocity of an object that moves in a circular path at any given point in the circle. If the car begins from rest, the only velocity is tangential velocity.
Therefore, if the car begins from rest, its velocity is at the end of one revolution around the circular track with a speed.
Learn more about centripetal force here:
https://brainly.com/question/898360
#SPJ11
which is easier: to detect the spread-out raw material in exoplanet systems from which planets might be assembled or to detect exoplanets after they are fully formed? in what region of the electromagnetic spectrum is this detection made?
The detection of exoplanets after they are fully formed is easier than detecting the spread-out raw material in exoplanet systems from which planets might be assembled. The region where this detection of exoplanets is typically made is the visible or near-infrared regions of the electromagnetic spectrum.
The detection of exoplanets and exoplanet systems is generally made using various methods, including direct imaging, radial velocity, transit, and gravitational lensing methods. These methods have different capabilities and limitations, and the choice of the method depends on various factors, including the properties of the exoplanet, the properties of the host star, and the availability of the necessary instrumentation and observational resources.
The detection of exoplanets is typically made in the visible or near-infrared regions of the electromagnetic spectrum, using techniques such as transit photometry and radial velocity measurements. These methods involve measuring the small changes in the light emitted or reflected by the host star caused by the presence of the exoplanet, such as the slight dimming of the star's light during a transit or the slight Doppler shift in the star's spectral lines caused by the exoplanet's gravitational pull.
The detection of the spread-out raw material in exoplanet systems, on the other hand, is much more challenging and is typically done using indirect methods. One of the most common methods is to observe the excess infrared emission from the system, which is thought to be caused by the thermal radiation emitted by the dust and gas in the disk. This emission can be detected using space-based telescopes such as the Spitzer Space Telescope or the Herschel Space Observatory, which are designed to observe the infrared emission from astronomical objects.
Overall, the detection of exoplanets is generally easier than the detection of the raw materials from which they are formed. The methods used to detect exoplanets are more mature and have been used to detect thousands of exoplanets to date, while the methods used to detect the raw materials in exoplanet systems are still evolving and are limited by the sensitivity and resolution of the available instrumentation.
Learn more about exoplanets here: https://brainly.com/question/29155216.
#SPJ11
what would its landing speed have been in the absence of air resistance? express your answer using two significant figures.
The landing speed of the ball in the absence of air resistance would be 14 m/s.
The landing speed of an object in the absence of air resistance can be calculated by considering the conservation of energy.
The initial energy of the object will be equal to the final energy of the object when it reaches the ground.
A ball falling from a height h with an initial velocity u.
The gravitational potential energy of the ball is given by mgh, where m is the mass of the ball, g is the acceleration due to gravity, and h is the height of the ball.
The kinetic energy of the ball is given by 1/2 mu², where u is the initial velocity of the ball.
At the ground level, the gravitational potential energy of the ball will be zero, and the kinetic energy of the ball will be given by 1/2 mv², where v is the velocity of the ball when it reaches the ground.
mgh + 1/2 mu² = 1/2 mv²
Solving for v, we get:
v = sqrt(2gh + u²)
In the absence of air resistance, the ball will continue to fall with an acceleration of g. Therefore, we can assume that the initial velocity u is equal to zero. Thus, the equation reduces to:
v = sqrt(2gh)
g = 9.8 m/s², we can calculate the landing speed of the ball for a given height h. For example, if the ball is dropped from a height of 10 meters, then the landing speed of the ball will be:
v = sqrt(2gh) = sqrt(2*9.8*10) = 14 m/s
Therefore, the landing speed of the ball in the absence of air resistance would be 14 m/s.
to know more about resistance refer here:
https://brainly.com/question/30799966#
#SPJ11
if normal atmospheric pressure is 14.7 pounds/sq in at the surface of the earth, what is the force pushing down on a table measuring 50 inches wide by 200 inches long?
The force pushing down on the table is 147,000 pounds.
Explanation:
To calculate the force pushing down on the table, we need to determine the area of the table in square inches, and then multiply that by the pressure exerted by the atmosphere.
The area of the table is 50 inches x 200 inches = 10,000 square inches.
The pressure exerted by the atmosphere is 14.7 pounds per square inch.
So the force pushing down on the table is:
10,000 square inches x 14.7 pounds per square inch = 147,000 pounds.
If normal atmospheric pressure is 14.7 pounds/sq in at the surface of the earth. The force pushing down on a table measuring 50 inches wide by 200 inches long is 147,000 pounds.
How To Count Force Pushing Down An Object?This is because the pressure is defined as force per unit area, and the area of the table is 50 inches x 200 inches = 10,000 square inches. So, if the normal atmospheric pressure at the surface of the earth is 14.7 pounds/square inch, then the force pushing down on the table is simply pressure x area = 14.7 pounds/square inch x 10,000 square inches = 147,000 pounds.
Learn more about force at https://brainly.com/question/12785175
#SPJ11
Research Galileo's work on falling bodies What did he wanted to demonstrate?What arguments did he use to prove that he was right?did be used experiments logic finding of other scientists or other approaches
Galileo Galilei conducted experiments on falling bodies to demonstrate that the rate of fall is independent of an object's mass. Galileo argued that if heavier objects did indeed fall faster, then two objects of different masses tied together would fall at an intermediate speed, which he found was not the case.
He used various methods to prove his point, including rolling balls down inclined planes, dropping weights from towers, and measuring the times of fall. He also used logic and mathematical reasoning to support his conclusions. Galileo's work marked a significant shift from traditional Aristotelian physics to the empirical approach of modern science.
To know more about modern science, here
brainly.com/question/30252960
#SPJ4