the student then prepares a solution using four pellets of naoh dissolved to 100.00 ml in a volumetric flask. the student slowly adds this to the khp solution to perform a titration. it requires 22.50 ml of the naoh solution to reach the endpoint. what is the molarity of the naoh solution based on this titration?

The variation in phase observed at room temperature can be explained by the presence of polar bonds in one structure as opposed to nonpolar bonds in the other structure.

Due to the formation of hydrogen bonds between highly electronegative atoms (F, O, and N) and hydrogen, they are stronger than dipole-dipole interactions. As compared to any polar bond that has dipole-dipole interactions, the dipole is stronger because of the greater electronegativity differential.

Dipole-dipole interactions, London dispersion interactions (sometimes referred to as Van der Waals interactions), hydrogen bonds, and ionic bonds are the four basic intermolecular interaction types in charge of a compound's physical characteristics.

To know more about polar bonds visit:-

https://brainly.com/question/10777799

#SPJ1

A valid electronic configuration should be written as: 1s² 2s² 2p⁶ 3s² 3p⁶ 4s² 3d¹⁰ 4p⁶ 5s² 4d¹⁰ 5p⁶ 6s² 4f¹⁴ 5d¹⁰ 6p⁶ 7s².


An electron configuration is used to show the distribution of electrons among the orbitals of an atom in its ground state, and it is written in the order of increasing energy of the orbitals.

Let's now figure out which of the following is an incorrect electron configuration.

2d5 is not a possible electron configuration according to the rules of electron configuration.

However, it is incorrect because, in the modern periodic table, the d orbital comes after the s orbital, so it should be written as: 1s² 2s² 2p⁶ 3s² 3p⁶ 4s² 3d¹⁰ 4p⁶ 5s² 4d¹⁰ 5p⁶ 6s² 4f¹⁴ 5d¹⁰ 6p⁶ 7s².

Learn more about electron configuration here:

https://brainly.com/question/29757010#

#SPJ11

The concentration of nitrate ions after mixing equal volumes of 1M NaNO3 and 1M KCl is 0.5M.

When equal volumes of 1M NaNO3 and 1M KCl are mixed, the nitrate ions (NO3-) and potassium ions (K+) will undergo a cation-anion exchange reaction to form potassium nitrate (KNO3) and sodium chloride (NaCl) as follows:

NaNO3 + KCl -> KNO3 + NaCl

The concentrations of Na+ and Cl- ions will remain unchanged after the reaction because they are spectator ions. However, the concentrations of NO3- and K+ ions will change.

Since the initial concentration of both NaNO3 and KCl is 1M, the initial concentration of NO3- is also 1M.

After the reaction, the moles of NO3- will be equal to the moles of K+ ions formed, which is 1/2 the initial concentration of KCl or 0.5M.

Therefore, the concentration of nitrate ions after mixing equal volumes of 1M NaNO3 and 1M KCl is 0.5M.

Learn more about concentration here : brainly.com/question/26811246

#SPJ1

Answer: 15.56 L of oxygen gas reacts to produce 56.1 grams of magnesium oxide at STP.

Explanation:

The given chemical equation represents the reaction between magnesium (Mg) and oxygen (O2) to form magnesium oxide (MgO) with a stoichiometric ratio of 2:1 between Mg and O2. This means that for every 2 moles of Mg that reacts, 1 mole of O2 is consumed.

The molar mass of MgO is 40.3 g/mol (24.3 g/mol for Mg + 16.0 g/mol for O). Therefore, the number of moles of MgO produced can be calculated as follows:

Number of moles of MgO = Mass of MgO / Molar mass of MgO

Number of moles of MgO = 56.1 g / 40.3 g/mol

Number of moles of MgO = 1.39 mol

Since the stoichiometric ratio of Mg to O2 is 2:1, we can calculate the number of moles of O2 consumed as follows:

Number of moles of O2 = (Number of moles of MgO) / 2

Number of moles of O2 = 1.39 mol / 2

Number of moles of O2 = 0.695 mol

At STP (standard temperature and pressure), one mole of any ideal gas occupies 22.4 L. Therefore, the volume of O2 consumed can be calculated as follows:

Volume of O2 consumed = Number of moles of O2 x 22.4 L/mol

Volume of O2 consumed = 0.695 mol x 22.4 L/mol

Volume of O2 consumed = 15.56 L

Therefore, 15.56 L of oxygen gas reacts to produce 56.1 grams of magnesium oxide at STP.

The Ultimate BOD ( Biochemical Oxygen Demand) of the waste is 81.3 mg/L when the 5-day BOD is 20 mg/L and the BOD rate coefficient is 0.15/day.

The Ultimate Biochemical Oxygen Demand (BOD) is defined as he quantity of oxygen required to stabilize or,

eliminate biodegradable organic matter in wastewater by the action of aerobic microorganisms under controlled laboratory conditions at a specified temperature over a period of time.

The 5-day BOD is measured by calculating the amount of oxygen consumed by microorganisms over a period of five days.

The Ultimate BOD of a waste can be determined by knowing the 5-day BOD and BOD rate coefficient. The following formula is used to determine the Ultimate BOD:

Ultimate BOD = 5-day BOD × [(e^(k×t))-1] / e^(k×t)Where k is the BOD rate coefficient and t is the time required to reach the Ultimate BOD.

The Ultimate BOD of the waste as follows: 5-day BOD = 20 mg/L k = 0.15/day t = ? Ultimate BOD = 5-day BOD × [(e^(k×t))-1] / e^(k×t) Ultimate BOD = 20 × [(e^(0.15×t))-1] / e^(0.15×t)

The Ultimate BOD is reached after 20 days. Ultimate BOD = 20 × [(e^(0.15×20))-1] / e^(0.15×20) Ultimate BOD = 81.3 mg/L

Therefore, the Ultimate BOD of the waste is 81.3 mg/L when the 5-day BOD is 20 mg/L and the BOD rate coefficient is 0.15/day. The coefficient is the numerical multiplier of a variable or quantity that follows a term or a factor.

To know more about Biochemical Oxygen Demand refer here:

https://brainly.com/question/29807316#

#SPJ11

The pH of a 0.20 M acetic acid solution is 2.72.

The pH of a 0.20 M acetic acid solution can be calculated using the Ka of acetic acid, CH3COOH, which is 1.8 x 10-5.

We will use the equation for the dissociation of acetic acid to calculate the pH of the solution.

CH3COOH(aq) + H2O(l) ⇌ H3O+(aq) + CH3COO-(aq)

The equilibrium constant expression for the dissociation of acetic acid is given by

Ka = [H3O+][CH3COO-] / [CH3COOH].

Since we know the value of Ka and the initial concentration of acetic acid, we can solve for

the concentration of H3O+.Ka = [H3O+][CH3COO-] / [CH3COOH]

1.8 x 10-5 = [H3O+]2 / 0.20[H3O+]2 = 3.6 x 10-6[H3O+] = 1.9 x 10-3 M

The pH of the solution can then be calculated as:

pH = -log[H3O+]pH = -log(1.9 x 10-3)

pH = 2.72

Therefore, the pH of a 0.20 M acetic acid solution is 2.72.

To know more about pH, refer here:

https://brainly.com/question/30255888#

#SPJ11

Methane can be produced from various natural and human-related activities. However, one activity that is not a source of methane is photosynthesis.

Methane is a potent greenhouse gas that can contribute to climate change. It has a much greater warming effect than carbon dioxide, although it stays in the atmosphere for a shorter period of time. The effects of methane emissions can include:

Learn more about emissions here https://brainly.com/question/14275614

#SPJ1

It is recommended to keep the reaction temperature low and the addition of nitric acid sulfuric acid mixture out slow because the reaction between the two is exothermic, which means it produces a lot of heat. The high temperature produced can result in an explosion, which can be dangerous.

The exothermic nature of the reaction causes the formation of nitronium ions, which act as an electrophile to nitrate the organic substrate. If the temperature is too high, the nitronium ions can form too fast, causing the reaction to run out of control. Additionally, the addition of the nitric acid sulfuric acid mixture should be slow to avoid the formation of nitrogen dioxide gas.

Nitrogen dioxide is produced when the nitric acid reacts with atmospheric nitrogen oxide. This can lead to a brown or yellow coloration of the reaction mixture and, in high concentration, can be toxic. By adding the mixture slowly, the concentration of nitrogen dioxide is reduced, making the reaction safer.

In conclusion, it is crucial to keep the reaction temperature low and add the nitric acid sulfuric acid mixture slowly to prevent an explosion from the high temperature produced by the exothermic reaction. The slow addition of the mixture also reduces the concentration of nitrogen dioxide, making the reaction safer.

To know more about Exothermic refer here:

https://brainly.com/question/3971357#

#SPJ11

Answer:

a. 3.19 m

b. 361.45 m

Explanation:

wavelength = speed of light ÷ frequency

speed of light = 3.00 x 10^8 m/s

AM is KILOhertz

830 kHz = 830,000 Hz

FM is MEGAhertz

93.9 MHz = 93,900,000 Hz

a.

wavelength = 3.00 x 10^8 m/s ÷ 830,000 Hz =

361.45 m

b.

wavelength = 3.00 x 10^8 m/s / 93,900,000 Hz = 3.19 m

Answer : 50 ml of a 6.00 M solution of sodium hydroxide must be diluted to 200 ml to make a 1.50 M solution of sodium hydroxide.

The volume (in ml) of concentrated sodium hydroxide solution (6.00 M) to be diluted to 200 ml in order to make a 1.50 M sodium hydroxide solution is 25.0 ml. Dilution of the solution is a process of reducing the concentration of a solute in a solution. It is the process of adding solvent or diluent to the solution to obtain a lower concentration of the solute in the solution.

Concentration (C) can be defined as the number of moles of solute (n) per volume of solution (V):C = n/VWe can derive a dilution equation from this definition: C1V1 = C2V2, where C1 is the initial concentration of the solute, V1 is the initial volume of the solution, C2 is the final concentration of the solute, and V2 is the final volume of the solution.

The number of moles of solute in the final solution is:n2 = C2 x V2We can substitute these values in the dilution equation to get: C1V1 = C2V2 Therefore: V1 = (C2V2)/C1 Substituting the given values in the above equation gives: V1 = (1.50 x 200)/6.00 = 50 ml

Know more about sodium hydroxide here:

https://brainly.com/question/29327783

#SPJ11

The molar concentration of the sodium hydroxide solution is 0.37 mol/L.

To determine the molar concentration of the sodium hydroxide solution, the following equation can be used:

Molarity = (Mass of Solute/Molecular Weight of Solute) / (Volume of Solution in L)

In this case, the solute is sodium hydroxide (NaOH) and the molecular weight of NaOH is 40.00 g/mol.

The mass of the solute must be calculated. Since 0.261 g of NaHC₂O₄ (one acidic proton) requires 17.5 ml of sodium hydroxide solution for a complete reaction, the mass of NaOH required must also be equal to 0.261 g since the equivalence of both is 1. Then the volume of the solution (in liters) is determined. Since 1 ml = 0.001 L, 17.5 ml = 0.0175 L.

Plugging the values into the equation gives:

Molarity = (0.261g/40.00 g/mol) / (0.0175 L) = 0.37 mol/L

Therefore, the molar concentration of the sodium hydroxide solution is found to be 0.37 mol/L  when 0.261 g of NaHC₂O₄ required 17.5 ml of sodium hydroxide solution for a complete reaction.

To know more about molar concentration, refer here:

https://brainly.com/question/15532279#

#SPJ11

False: Lindeman's law of trophic efficiency, which says that the efficiency of energy transferred from one trophic level to the next higher trophic level is about 10%, states that the transfer of energy from one trophic level to the next trophic level follows a 10% rule.

Energy transfer between trophic levels is inefficient. Only 10% or so of the net output at one level carries over to the next level. Ecological pyramids are diagrams that show the flow of energy, the accumulation of biomass, and the quantity of organisms at various trophic levels.

The ten percentile rule is usually used to describe how energy is transferred between trophic groups. 90% of the initial energy from one trophic level to the next is inaccessible because it is used for activities like movement, growth, respiration, and reproduction.

To know more about energy visit:-

https://brainly.com/question/8630757

#SPJ9

The correct formula for the precipitate formed when aqueous solutions of [tex]FeCl_{3}[/tex] and [tex](NH_{4})2S[/tex] are mixed is [tex]Fe_{2}S_{3}[/tex].

А precipitаte is аn insoluble solid thаt forms from а chemicаl reаction in а solution. It hаppens when two solutions thаt contаin soluble sаlts аre mixed, аnd а new insoluble sаlt is formed. In this cаse, when аqueous solutions of [tex]FeCl_{3}[/tex] аnd [tex](NH_{4})2S[/tex] аre mixed, а solid precipitаte forms.

To determine the correct formulа for the precipitаte, we need to consider the reаction thаt tаkes plаce during mixing. Aqueous solutions of [tex]FeCl_{3}[/tex] and [tex](NH_{4})2S[/tex] react to form [tex]Fe_{2}S_{3}[/tex] (Iron(III) sulfide) and [tex]6NH_{4}Cl[/tex] (Ammonium chloride) as shown below:

[tex]Fe_{2}S_{3}[/tex] (aq) + 3 [tex](NH_{4})2S[/tex] (aq) → [tex](NH_{4})2S[/tex] (s) + [tex]6NH_{4}Cl[/tex] (aq)

So the correct formula for the precipitate formed is [tex]Fe_{2}S_{3}[/tex].

For more information about precipitate refers to the link: https://brainly.com/question/29762381

#SPJ11

Answer: The compound of bromine and fluorine used to make UF6 has an empirical formula of BrF8, which contains 1 atom of bromine and 8 atoms of fluorine. This compound is composed of 58.37 mass percent bromine and 41.63 mass percent fluorine.

The compound of bromine and fluorine used to make UF6 is composed of 58.37 mass percent bromine. To determine its empirical formula, we can use the following equation:

Molecular Mass = Mass Percent Bromine/Atomic Mass Bromine * Number of Bromine Atoms + Mass Percent Fluorine/Atomic Mass Fluorine * Number of Fluorine Atoms

Using this equation, we can determine the empirical formula by rearranging the equation and making it easier to calculate. To do this, we can make all terms on the right side of the equation be a multiple of the smallest mass percent of the elements in the compound. In this case, the smallest mass percent is bromine, so we must make the fluorine mass percent be a multiple of 58.37.

58.37/Atomic Mass Bromine * Number of Bromine Atoms = Mass Percent Fluorine/Atomic Mass Fluorine * Number of Fluorine Atoms

Using this equation, we can calculate the number of bromine atoms and fluorine atoms. The atomic mass of bromine is 79.9 and the atomic mass of fluorine is 19. In this equation, the number of bromine atoms is 1, and the number of fluorine atoms is 8. This results in an empirical formula of BrF8.

In conclusion, the compound of bromine and fluorine used to make UF6 has an empirical formula of BrF8, which contains 1 atom of bromine and 8 atoms of fluorine. This compound is composed of 58.37 mass percent bromine and 41.63 mass percent fluorine.


Learn more about compounds here:

https://brainly.com/question/23334479#

#SPJ11

The temperature should be raised by 28.15°C to run 100 times faster than it does at room temperature with the catalyst.

To determine the temperature increase needed to make the catalyzed reaction run 100 times faster, we can use the Arrhenius equation:

[tex]k_{2}[/tex]/[tex]k_{1}[/tex] = e^(-Ea/R * (1/[tex]T_{2}[/tex] - 1/[tex]T_{1}[/tex])

Where [tex]k_{1}[/tex] and [tex]k_{2}[/tex] are the rate constants at temperatures [tex]T_{1}[/tex] and [tex]T_{2}[/tex], Ea is the activation energy (98.4 kJ mol-1), and R is the gas constant (8.314 J [tex]K^{-1}[/tex] [tex]mol^{-1}[/tex]).

Since we want the reaction to be 100 times faster, k2/k1 = 100. Now we can rearrange the equation and solve for [tex]T_{2}[/tex]:

1/[tex]T_{2}[/tex] - 1/[tex]T_{1}[/tex] = -R * ln(100)/Ea

Assuming room temperature ([tex]T_{1}[/tex]) is 298 K (25°C), we can plug in the values:

1/[tex]T_{2}[/tex] - 1/298 = -8.314 * ln(100)/98,400

1/[tex]T_{2}[/tex] = 1/298 + (8.314 * ln(100)/98,400)

[tex]T_{2}[/tex] = 1 / (1/298 + (8.314 * ln(100)/98,400))

Now, calculate the value of [tex]T_{2}[/tex]:

[tex]T_{2}[/tex] ≈ 326.3 K

To convert [tex]T_{2}[/tex] to °C, subtract 273.15:

[tex]T_{2}[/tex] = 326.3 - 273.15 ≈ 53.15°C

Therefore, you would need to raise the temperature by approximately 28.15°C (53.15 - 25) to make the catalyzed reaction run 100 times faster.

To know more about Arrhenius Equation:

https://brainly.com/question/16994409

#SPJ11

The pH of the solution after 13.2 mL of barium hydroxide has been added is 13.69. The volume of the hydrocyanic acid solution is 26.5 mL, which is 0.0265 L.

The balanced equation for the reaction between hydrocyanic acid and barium hydroxide is:

2 HCN + Ba(OH)2 → Ba(CN)2 + 2 H2O

This reaction is a neutralization reaction, which means that the number of moles of acid is equal to the number of moles of the base at the equivalence point. We can use this information to calculate the number of moles of barium hydroxide that have reacted with the hydrocyanic acid.

n(Ba(OH)2) = M(Ba(OH)2) x V(Ba(OH)2)

where M(Ba(OH)2) is the molarity of the barium hydroxide solution and V(Ba(OH)2) is the volume of barium hydroxide solution added.

Using the given values, we have:

n(Ba(OH)2) = 0.489 mol/L x 0.0132 L

= 0.00646 mol

Since the stoichiometry of the reaction is 2:1 for HCN to Ba(OH)2, the number of moles of HCN that have reacted is half the number of moles of Ba(OH)2:

n(HCN) = 0.5 x n(Ba(OH)2)

= 0.5 x 0.00646 mol

= 0.00323 mol

The volume of the hydrocyanic acid solution is 26.5 mL, which is 0.0265 L. Thus, the initial concentration of hydrocyanic acid is:

M(HCN) = n(HCN) / V(HCN)

= 0.00323 mol / 0.0265 L

= 0.122 M

At the equivalence point, all of the hydrocyanic acids have reacted, so the concentration of hydroxide ions (OH-) in the solution is equal to the concentration of barium hydroxide:

[OH-] = M(Ba(OH)2) = 0.489 M

The hydrocyanic acid dissociates in water to form hydrogen cyanide and hydronium ions (H3O+):

HCN + H2O ⇌ CN- + H3O+

The equilibrium constant expression for this reaction is:

Ka = [H3O+][CN-] / [HCN]

The value of Ka for hydrocyanic acid is 4.9 x 10^-10.

At the equivalence point, all of the hydrocyanic acids have reacted, so the concentration of hydrogen cyanide and hydronium ions is zero. The concentration of hydroxide ions can be used to calculate the concentration of hydronium ions using the equation:

Kw = [H3O+][OH-]

where Kw is the ion product constant for water, which has a value of 1.0 x 10^-14 at 25°C.

Rearranging the equation gives:

[H3O+] = Kw / [OH-]

= 1.0 x 10^-14 / 0.489

= 2.04 x 10^-14 M

Taking the negative logarithm of this value gives:

pH = -log[H3O+]

= -log(2.04 x 10^-14)

= 13.69

To learn more about barium hydroxide

https://brainly.com/question/30888146

#SPJ4

The combination of elements that are required for a compound to be considered organic are carbon and hydrogen. The correct answer among the given options is carbon and hydrogen.

Organic compounds are the fundamental components of life and are classified by the presence of carbon atoms, which are covalently linked to one another and to other elements such as oxygen, nitrogen, and sulfur, as well as by the lack of ionic bonding.

To summarize, an organic compound is a compound that contains carbon atoms bonded to hydrogen atoms, among other elements, in a covalent bond. The majority of organic compounds contain a carbon-carbon bond, which is the foundation of organic chemistry.

The following are some examples of organic compounds:

Methane, CH4

Ethanol, C2H5OH

Ethanoic acid, CH3COOH

Acetone, (CH3)2CO

Amino acid glycine, NH2CH2COOH

As a result, the correct combination of elements that are required for a compound to be considered organic are carbon and hydrogen.

For more such questions on elements, click on:

https://brainly.com/question/28424113

#SPJ11

The amount of kinetic energy required to strain the chemical bonds in substrates so they can achieve the transition state is the definition of activation energy.

What is Activation Energy?

Activation energy is the amount of energy required for a chemical reaction to occur. The energy that must be provided to molecules in order for them to react with one another is known as activation energy.

This can be accomplished in a variety of ways, such as by increasing the temperature or pressure, adding a catalyst, or irradiating the reactants with light.

Activation energy is defined as the energy required for the reaction to begin. It's the energy that molecules require to overcome the initial barrier so that a reaction may proceed.

When a chemical reaction occurs, the reactants must collide with one another with sufficient force and in the appropriate orientation to form products.

It's critical to note that activation energy is a form of potential energy that isn't included in the overall energy change of a reaction.

To learn more about activation energy refer: https://brainly.com/question/11291663

#SPJ11

Osmotic pressure is needed to stop the movement of solvent through a membrane.

Osmotic pressure is created when a solution is separated from a more concentrated solution, resulting in molecules of the solvent moving towards the more concentrated solution.

In order for the solvent molecules to not move through the membrane, the pressure on either side must be equal, which is why osmotic pressure is needed.

Osmotic pressure is measured in atmospheres and can be increased through the addition of more molecules to the solution or decreased through the removal of molecules.

Solvent molecules are required to maintain osmotic pressure, since they move between the two solutions. In a system where osmotic pressure is maintained, no solvent molecules will pass through the membrane.

The number of solvent molecules on either side of the membrane must be equal in order for the pressure on each side to remain balanced.

An increase or decrease in the number of molecules on one side of the membrane can cause the pressure to become imbalanced and result in the solvent molecules passing through the membrane.

An increase in temperature can also cause the pressure on either side of the membrane to become imbalanced, and result in the movement of the solvent molecules through the membrane.

An increase in temperature can cause the molecules to expand, resulting in an increase in pressure on one side and a decrease on the other.

An decrease in temperature can have the opposite effect, causing the pressure on both sides of the membrane to decrease, resulting in the movement of the solvent molecules.

In conclusion, osmotic pressure is needed to stop the movement of solvent through a membrane, and is maintained by having an equal number of solvent molecules on either side of the membrane.

An increase or decrease in temperature can also affect the osmotic pressure, resulting in the movement of the solvent molecules through the membrane.

to know more about Osmotic pressure refer here:

https://brainly.com/question/29819107#

#SPJ11

The statement that correctly defines chemical equilibrium is, "Chemical equilibrium occurs when free energy exists in the lowest possible value."

Chemical equilibrium is a state in which the forward and reverse chemical reactions take place at the same rate. The point at which this occurs is referred to as the equilibrium point.

The forward and backward reactions that result in chemical equilibrium continue to occur; they just occur at the same speed, resulting in no net change in the system's chemical concentration over time.

The Gibbs free energy of a chemical reaction determines the spontaneity of the reaction. If the ΔG value is positive, the reaction is non-spontaneous; if the ΔG value is negative, the reaction is spontaneous; and if the ΔG value is zero, the system is in equilibrium. In equilibrium, the free energy exists in the lowest possible value.

To learn more about chemical equilibrium refer: https://brainly.com/question/30884265

#SPJ11

A wavelength of [tex]10^{-2}[/tex] meters corresponds to a frequency of about 3 × [tex]10^{14}[/tex] Hz, which places it in the microwave range of the electromagnetic spectrum.

Therefore, the type of radiation that would have a wavelength of [tex]10^{-2}[/tex]meters is a microwave radiation. Microwaves are a type of electromagnetic radiation that has a longer wavelength than visible light but shorter than radio waves. They are commonly used in communication, heating, and cooking applications. In particular, microwave radiation is used in microwave ovens to heat food by causing water molecules to vibrate, which generates heat. Additionally, microwave radiation is used in telecommunications, such as mobile phones and satellite communications.

To know more about corresponds click here:

brainly.com/question/26104021

#SPJ4

The stoichiometric factor is 6:1 that is 6 moles of [tex]Na_2S_2O_3[/tex] reacts with one mole of [tex]KIO_3[/tex]

The stoichiometric factor is a factor that shows the number of moles of a reactant or product that takes part in the chemical reaction. The balanced chemical equation provides the ratio of the reactants and products involved in a chemical reaction.

It is used to determine the stoichiometric factor which is the number of moles of a compound in a balanced equation.

The balanced equation for the given reaction is:

[tex]Na_2S_2O_3 + 2KIO_3 + H_2O \rightarrow I_2 + 2NaHSO_4 + 2KHSO_4[/tex]

First, write the balanced equation of the reaction between

[tex]Na_2S_2O_3 \times 2H_2O\ and\ KIO_3.KIO_3 + 6Na_2S_2O_3 + 9H_2O \rightarrow 3I_2 + 6Na_2SO_4 + 9H_2SO_4[/tex]

So, the stoichiometric factor, that is the number of moles, of [tex]Na_2S_2O_3\times 2H_2O[/tex] reacting with one mole of [tex]KIO_3[/tex] is 6 moles.

Therefore, 6 moles of  [tex]Na_2S_2O_3\times 2H_2O[/tex] are needed to react with one mole of [tex]KIO_3[/tex].

To learn more about stoichiometry refer: https://brainly.com/question/15097460

#SPJ11

The percent yield of carbon dioxide is 66.90%.

To calculate the percent yield of carbon dioxide, we need to compare the actual yield of carbon dioxide with the theoretical yield of carbon dioxide that would be expected from the balanced chemical equation.

Let's say the chemical equation for the reaction that produces carbon dioxide is:

2 A + 3 B → 2 CO2 + C

Assuming that carbon dioxide is the only product, we can calculate the theoretical yield of carbon dioxide from the given amount of reactants used in the reaction.

If we know the mass of the limiting reactant that was used, we can use stoichiometry to calculate the theoretical yield of carbon dioxide.

Let's say that we used 5.0 g of reactant A, and that reactant A is the limiting reactant. If we know the molar mass of reactant A and the stoichiometric coefficients of the reactants and products in the equation, we can calculate the theoretical yield of carbon dioxide:

Calculate the number of moles of reactant A used:

moles of A = mass of A / molar mass of A

Use the stoichiometry of the equation to calculate the number of moles of carbon dioxide produced:

moles of CO2 = (moles of A) x (2 moles of CO2 / 2 moles of A)

Calculate the mass of carbon dioxide produced:

mass of CO2 = moles of CO2 x molar mass of CO2

Once we have calculated the theoretical yield of carbon dioxide, we can calculate the percent yield by dividing the actual yield by the theoretical yield and multiplying by 100:

percent yield = (actual yield / theoretical yield) x 100

Let's assume that the theoretical yield of carbon dioxide is calculated to be 7.25 g based on the amount of reactants used. If the actual yield of carbon dioxide is measured to be 4.85 g, the percent yield can be calculated as follows:

percent yield = (4.85 g / 7.25 g) x 100

percent yield = 66.90%

Learn more about  percent yield

https://brainly.com/question/17042787

#SPJ4

2 ml of the 50 mg/ml BSA stock solution is required to be added to the new vessel in order to make the final volume of 10 ml.

If we are not having 10 ml of a 10 mg/ml BSA solution, we then we are required to make it by adding some additional solvent or buffer to dilute the stock solution.

Let us assume that we are having some BSA stock solution, let's say 50 mg/ml, and we need 10 ml of 10 mg/ml BSA solution, we can use the following formula to calculate the required amount of stock solution and solvent:

C1V1 = C2V2

(Here, C1 is the concentration of the stock solution (50 mg/ml), V1 is the volume of the stock solution we need to use (which is unknown), C2 is the desired concentration (10 mg/ml), and V2 is the final volume we want to achieve (i.e. 10 ml).

Rearranging the formula above , we will be getting,

V1 = (C2V2)/C1

Substituting the values we have in the equation,  we will be getting,

V1 = (10 mg/ml x 10 ml)/50 mg/ml = 2 ml

Therefore it can be said that we are needed to take 2 ml of the 50 mg/ml BSA stock solution and add it to the new vessel. To make the final volume 10 ml, we need to add 8 ml of the appropriate solvent or buffer.

Learn more about concentration of solutions :

https://brainly.com/question/15458177

#SPJ4

The volume of NaOH required to reach the equivalence point in the titration of a strong acid is typically smaller than the volume of NaOH required to reach the equivalence point in the titration of a weak acid.

This is because the strong acid is more reactive and therefore requires less base to neutralize it.

In a titration, the volume of a base (such as NaOH) required to reach the equivalence point is determined by the strength of the acid being titrated.

Generally speaking, a stronger acid will require a smaller volume of base than a weaker acid to reach the equivalence point.

This is because the stronger acid is more reactive, and it therefore requires less base to neutralize it.

When titrating a strong acid with a base such as NaOH, the equivalence point is reached when the number of moles of the acid is equal to the number of moles of the base.

In this situation, a relatively small volume of base will be required to completely neutralize the acid.

On the other hand, when titrating a weak acid with NaOH, the equivalence point is reached when the pH of the solution reaches the pKa of the acid.

This requires a much larger volume of NaOH than is required for titrating a strong acid, as the weak acid is much less reactive and therefore requires a larger volume of base to neutralize it.

In summary, the volume of NaOH required to reach the equivalence point in the titration of a strong acid is typically smaller than the volume of NaOH required to reach the equivalence point in the titration of a weak acid.

This is because the strong acid is more reactive and therefore requires less base to neutralize it.

to know more about titration refer here:

https://brainly.com/question/29590776#

#SPJ11

At standard pressure, which substance becomes less soluble in water as temperature increases from 10.°C to 80.°C is : d. NH4Cl

Solubility of substance increases with temperature, as higher temperatures allow more particles to dissolve in solvent. However, there are some exceptions, where solubility decreases with increasing temperature.

In this case, we are looking for substance that becomes less soluble in water as temperature increases from 10°C to 80°C at standard pressure.

The correct answer is d. NH4Cl.

At standard pressure, solubility of NH4Cl decreases with increasing temperature due to its endothermic dissolution process. As temperature increases, heat absorbed by the solution also increases, which makes dissolution process less favorable. Therefore, solubility of NH4Cl decreases with increasing temperature.

To know more about solubility, refer

https://brainly.com/question/23946616

#SPJ1

Friedel crafts acylation is preferred over Friedel craft alkylation. Friedel crafts acylation reactions have many benefits as compared to Friedel crafts alkylation reactions.

Friedel-Crafts acylation and Friedel-Crafts alkylation reactions are both types of electrophilic substitution reactions that involve the formation of carbocations as intermediates. However, acylation is preferred over alkylation in certain situations.

Here are some benefits of Friedel-Crafts acylation reactions compared to Friedel-Crafts alkylation reactions:

1. Friedel-Crafts acylation reactions produce pure compounds as their major products because they do not involve any byproducts like Friedel-Crafts alkylation reactions.

2. The yields of Friedel-Crafts acylation reactions are often higher than those of Friedel-Crafts alkylation reactions.

3. Friedel-Crafts acylation reactions are more selective than Friedel-Crafts alkylation reactions because the acyl group is a better electrophile than the alkyl group.

4. The carbonyl group in the acylating agent (usually an acid chloride) can be selectively protected or modified using a variety of functional groups without affecting the aromatic ring. This is not possible in Friedel-Crafts alkylation reactions.

5. Friedel-Crafts acylation reactions can be carried out with a wider range of substrates (such as anisole or benzene) than Friedel-Crafts alkylation reactions.

6. The products of Friedel-Crafts acylation reactions are often more reactive than the starting materials, which allows for further functionalization or modification of the aromatic ring.

Learn more about Friedel-Crafts reaction - https://brainly.com/question/30861499#

#SPJ11

The osmotic pressure of a solution made by dissolving 7.19 g of glucose in 18.9 ml of solution at 17.4°C can be calculated using the formula: Osmotic Pressure (atm) = Molarity (M) × Gas Constant (R) × Temperature (T).

Molarity = (Mass of Solute/ Molar Mass of Solute) / Volume of Solution
= (7.19 g / 180.2 g/mol) / 18.9 ml
= 0.3999 M

Gas Constant (R) = 0.08206 liter atm/mol K
Temperature (T) = 17.4°C + 273.15 = 290.55 K

Therefore, Osmotic Pressure (atm) = 0.3999 M × 0.08206 liter atm/mol K × 290.55 K
= 0.983 atm

The osmotic pressure of a solution is the hydrostatic pressure required to balance the osmotic pressure of a solution. This is determined by the concentration of the solute molecules, temperature, and the properties of the solvent. The osmotic pressure of a solution can be used to determine the boiling point, vapor pressure, and vapor pressure of a solution. Additionally, it is important for the transport of substances across biological membranes, as well as for the stability of colloidal suspensions.

In summary, the osmotic pressure (in atm) of a solution made by dissolving 7.19 g of glucose in 18.9 ml of solution at 17.4°C can be calculated using the formula: Osmotic Pressure (atm) = Molarity (M) × Gas Constant (R) × Temperature (T), and is equal to 0.983 atm.

To know more about osmotic pressure click on below link :

https://brainly.com/question/15501096#

#SPJ11

Maxwell's relations can be used to show how the enthalpy of an ideal gas changes with volume held at constant temperature. This is how it's done:
Using the fundamental equation, dU = TdS - PdV, and taking the partial derivative with respect to volume,
we get:dU/dV = T(dS/dV) - P This equation represents the relationship between internal energy and volume for a constant temperature process.

Using the Maxwell relation, dS/dV = (dP/dT)/T,
we can substitute it in the previous equation: dU/dV = T(dP/dT)/T - PdU/dV = (dP/dT) - P
This equation represents the relationship between internal energy and volume for a constant temperature process.
The enthalpy, H = U + PV, can then be used to express the result as:dH/dV = dU/dV + P + V(dP/dT)dH/dV = (dP/dT)V

The above equation shows how the enthalpy of an ideal gas changes with volume held at constant temperature. Therefore, we can conclude that the enthalpy of an ideal gas is dependent on the temperature and the pressure of the gas.

To learn more about "Maxwell relation" here:

https://brainly.com/question/28956380#

#SPJ11

The one IV bag of potassium chloride 10 meq in d5w 50 ml IV should last 24 hours  and is because the rate is set at 50 ml/hr, so after 24 hours, the full 50 ml of the IV bag will have been infused.

To calculate the duration of the IV bag, you need to divide the total volume (50 ml) by the rate (50 ml/hr). This gives you a duration of 1 hour.

To convert this to 24 hours, you need to multiply the result by 24, giving you a total of 24 hours.

Therefore, the one IV bag of potassium chloride 10 meq in d5w 50 ml IV should last for 24 hours when given at a rate of 50 ml/hr.

To know more about potassium chloride  click on below link:

https://brainly.com/question/22528097#

#SPJ11